Edge CE-670-FDV SERIES User Manual Download Page 26

As Limited Below,

Edge Industries, Inc., warrant to the original retail purchaser that this Cutters Edge Saw is free from defects in materials and workmanship and agree to
repair and/or replace any defective saw part or component free of charge as follows:

1.

Parts other than electronic ignition parts.

At not cost to the original retail purchaser, Edge Industries, Inc., will replace defective parts supplied or manufactured by Edge Industries, Inc:
A. For one year from date of original purchase when used for fire department applications.
B. For thirty days from date of original purchase when saw is used for commercial purposes, except as listed below in section 2.
C. A saw is used for commercial purposes when it is used to derive income.

2.

Extended warranty.

Selected saw models used commercially may have warranty extended.
Electronic ignition parts.
A. For six months from the date of original purchase, Edge Industries, Inc., will replace any defective electronic ignition parts supplied or manu-

factured by Edge Industries, inc. at no cost to the original purchaser.

B. For a period starting six months and ending one year after the original retail purchase, Edge Industries, Inc., will replace any defective elec-

tronic ignition parts supplied or manufactured by Edge Industries, inc. at a charge to the original purchaser of 50% of Edge Industries'suggested

retail price.

Engine parts.

A. For six months from date of original purchase, Edge Industries, Inc., will replace any defective engine part supplied or manufactured by Edge

Industries, inc. at no cost to the original purchaser subject to the limitations of paragraph 5 below.

B. Engine parts are limited to cylinder assembly, crankshaft, crankcase and flywheel.

3.

Labor.

For thirty days from the date of original purchase, an authorized Edge Industries, Inc., dealer will provide labor at no charge to the original retail
purchaser for the replacement of any defective part supplied or manufactured by Edge Industries, Inc.

4.

Grantor of Warranty:

Edge Industries, Inc.
1435 Manzanita Drive

Julian, CA 92036 U.S.A.
760-765-0597

CUTTERS EDGE

LIMITED WARRANTY

Effective 7-1-92

OPERATION & MAINTENANCE / 26

5.

Limitations on Warranty:

This warranty is not transferable, does not cover damage caused by unreasonable use or damage resulting from other than defects in material or
workmanship, does not cover damages contributed to by a failure to provide reasonable and necessary maintenance, does not cover engine fail-
ure due to lack of or improper lubrication. Tuneups or replacement of non-defective parts-such as mounts, starter springs, ropes, spark plugs, and
filters-that may be expected to wear out with reasonable use during the warranty period are not covered. This warranty applies only to saws sold
through dealers appointed by Edge Industries, Inc.

THE WARRANTOR WILL BE LIABLE FOR NO INCIDENTAL OR CONSEQUENTIAL DAMAGES. THERE ARE NO EXPRESS WARRANTIES
OTHER THAN THOSE SET FORTH ABOVE. ANY WARRANTY IMPLIED BY STATE LAW-WHETHER MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE OR OTHERWISE SHALL BE EFFECTIVE ONLY FOR THE DURATION OF THE APPLICABLE WARRANTY PERI-
OD LISTED ABOVE. Some states do not allow exclusions of incidental or consequential damages and/or limitations on how long an implied war-
ranty lasts, so the above exclusions and limitations may not apply to you.

6.

Responsibilities of me purchaser under this Warranty:

A. To deliver or ship the saw covered under this Warranty to the dealer from whom it was originally purchased or to an Edge Industries, Inc.Ñ autho-

rized servicer center. Time limits on warranties are measured to the date of delivery or shipment.

B. Freight costs, if any, will be borne by the purchaser.
C. To provide reasonable care and maintenance of the Edge Industries, Inc., product.

7.

Timely repair of warranted product:

Any product which qualifies under this Warranty shall be repaired in a timely manner, consistent with the normal work flow at the servicing location
and depending on the availability of replacement parts.

8.

Purchaser rights and remedies:

This Warranty gives you specific legal rights. You may also have other rights which vary from state to state. If you do not receive satisfactory results
from authorized servicing stations, you may contact Edge Industries, Inc., Customer Relations Department, PO. Box 1179, Julian, CA 92036.

CUTTERS EDGE FIRE RESCUE SAWS

Summary of Contents for CE-670-FDV SERIES





























Reviews: