Edge Lighting PSB-30-12VDC Installation Instructions Manual Download Page 1

PSB-30-12VDC

Installation Instructions for 

30 Watt 12 Volt DC LED Power Supply 

1

904-PSB-30-12VDC-04

1718 W. Fullerton Ave

Chicago, IL 60614

Tel: 773-770-1195

Fax: 773-935-5613

www.edgelighting.com

[email protected]

SAVE THESE INSTRUCTIONS!

- Do not install this power supply in a wet location.

- To reduce the risk of the system overheating and possibly 
  causing a fire, make sure all the connections are tight. 

- Do not install *LED fixture closer than three inches or as 
  specified in the *LED fixture installation instructions to 
  curtains or similarly combustible materials. Keep insulation 
  at least 3" away from the enclosure.

- Turn the electrical power off before modifying the lighting 
  system in any way.

- The system is "ETL" listed for USA and Canada only when 
  all the products used are supplied by Edge Lighting.

* See LED fixture installation instructions for proper 
   placement.

RISK OF FIRE:

 This product must be installed by a 

  qualified electrician. Turn the power to the electrical box off 
  during installation. Read the "Important Safety Instructions "
  before installation.

NOTE:

 To avoid overheating the power supply, install it in a     

  ventilated remote location where air flows. Maintain proper  
  spacing among power supplies when multiple power  
  supplies are installed in the same remote location.

- This product is not suitable for wet locations. It is approved 
  for the use at any height above the finished floor.

-  A typical installation is shown. Specific installation must be 
  in accordance with the local electrical codes.

TO REDUCE RISK OF FIRE, 

it is important to wire the 

  power supply for the system as described in this 
  installation instruction.

- Load the power supply to 

MAXIMUM 30

 Watts.

- Use Lightolier "ZP600FAM120" 0-10 volt controller to dim 
  the Warm White LED soft strip.

- Use CDP color dial or CTP color touch screen controller with 
  RGB LED soft strip. 

GENERAL INFORMATION

IMPORTANT SAFETY INSTRUCTIONS

LOW VOLTAGE WIRE SIZE CHART

POWER SUPPLY
WATTAGE

WIRE SIZE
UP TO 26 FT

WIRE SIZE
FOR 27-41 FT

WIRE SIZE
FOR 42-68 FT

WIRE SIZE
FOR 69-100 FT

30 WATT

12 Volt

#14 GA

#12 GA

#10 GA

#8 GA

© 2015 Edge Lighting. All Rights Reserved. 

Summary of Contents for PSB-30-12VDC










Reviews: