background image

 

 

Quick Installation Guide 

ECWO5210-L  Outdoor  Access  Point 

ENGLISH 

 

CE CAUTION 

 

Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive) for   

European Community, Switzerland, Norway, Iceland, and Liechtenstein   

Model: ECWO5210-L 

For 2.4 GHz radios, the device has been tested and passed the requirements of the following standards, and 

hence fulfills the EMC and safety requirements of R&TTE Directive within the CE marking requirement. 

• Radio: EN 300.328

:

 

• Radio: EN 50392 

• EMC: EN 301.489-1, EN 301.489-17,   

• EMC: EN 55022

 

Class B, EN 55024

:

+ A1 + A2

 

including the followings: 

      EN 61000-3-2, EN 61000-3-3. 

      EN 61000-4-2, EN 61000-4-3, EN 61000-4-4,   

      EN 61000-4-5, EN 61000-4-6, EN 61000-4-11 

• Safety: EN 60950-1 + A11, 

 

Caution:

   

 

This declaration is only valid for configurations (combinations of software, firmware, and hardware) 

provided and supported by Edgecore Networks Corporation. The use of software or firmware not provided 

and supported by Edgecore Networks Corporation. may result in the equipment no longer being 

compliant with the regulatory requirements.   

European  standards  dictate  maximum  radiated  transmit  power  of  100mW  EIRP  and  frequency  range 

2.400-2.4835 GHz. This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be 

restricted  to  certain  frequencies  and/or  may  require  a  license  for  operation.  Contact  your  local  regulatory 

authority for compliance. 

 

Summary of Contents for ECWO5210-L



















Reviews: