background image

 

 
 

OPERATING INSTRUCTIONS

 

 

1.  Start and select working mode 

   

Or 

    

 

Turn the heater on by pressing the Power button on the 
control panel or by pressing the Power button on the supplied 
remote control. 

Once power is off, heating element will stop working at first.  
The fan will continue to run for approximately three minutes 
to emit residual heat inside of the unit. 

 

    

Or 

    

 

Select a heat setting. 

Press the Mode button to alternate between the two heat 
settings.

 

 

Under Auto heat-up mode, when the value difference 
between set temp and room temp exceeds 5°F or so, the unit 
will run at full 1500W, otherwise runs at 750W; Under High 
heat-up mode, the unit runs at a stable 1500W, when room 
temp exceeds 86°F, heat-up stops.

  

 

2.  Setting room temperature 

     Caution! Only in Auto heat-up mode can setting temperature be performed.    

 

    Or 

  

  

Or 

    

Or 

   

 

Adjust the thermostat by pressing the arrows on the control 
panel or remote control. 

 

Set temperature indication varies from 64°F to 86°F. Once 
you have chosen the desired temperature, the heater will 
remain on until the room temperature increases to the 
temperature on the digital display. The heater will cycle on 
and off to maintain the desired room temperature. 

 

 

 

 

 

 

 

Summary of Contents for A5834










Reviews: