Eden SOFT NC Installation, Operation And Maintenance Manual Download Page 7

Vers. 2015-3

7

INSTALLATION, OPERATION

AND MAINTENANCE MANUAL

water cassette

SOFT / SOFT-ECM

RECEIVING, STORE AND MOVING THE UNITS

INSTALLATION ACCESSORIES

SELECTION OF CASSETTE INSTALLATION LOCATION

At the moment of the delivery of the unit, make sure that it corresponds to the 

one indicated on the  transport document. Check the integrity of the packing 
and the unit. Should there be any differences with the original order or any 

damages, anomalies, or incomplete supply, please point it out on the delivery 

note and inform the firm straight away. Never install or use damaged appara

-

tuses. The unit can be stored in room protected from bad weather with tem

-

perature between the +4°C and the

 +40°C. Transport the packed unit near as  

possible to the installation place. To avoid any damage to the unit, the plastic 
part (frontal panel and grille) are furnished separately. The handling and the 

installation could be facilitated cy use of an elevator 

(Pic. 04).

Is included in the delivery nr. 1 c

ardboard mounting template to position the unit 

during the installation phase.

RECCOMENDATION!

- The unit must be installed in a solid and vibration-free ceiling. 
- There should be no obstruction of the air flow into and out of the unit and the 
air should be evenly distributed throughout the whole room.
- Do not install the unit near sources of heat, steam or inflammable gases.

- Install the unit near an electric socket or connect it directly to the power

supply.
- Do not install the unit in a place, which is exposed to direct sunSOFT.
- The selected place should allow easy drainage of the condensed water.
- Periodically check appliance operation and leave sufficient space for mainte

-

nance around the appliance, as shown in the picture 05.
- Install the unit so that the filter is easily accessible.

FIXING THE PANEL

After installation of the unit, mount the grille using the 4 screws provided 

(pic. 09).

ATTENTION: It is very important to fix the grille in the right position for 
correct connection of the receiver panel to the unit.

Establish the position and size of the hole in the ceiling using the cardboard 
mounting template (pic. 06).

 

To fix the unit to the ceiling, use the threaded bar and suitable screw anchors as 
shown in pic. 07

 (material not included in the supply). 

 

Use a spirit level

 (Pic. 08), 

to make sure that the unit is level and check that it is 

securely fixed to the ceiling. In high humidity environments, metal supports must 

be insulated using adhesive insulating material

.

Pic. 04

Pic. 05

Pic. 06

Pic. 07

Pic. 08

Pic. 09

ATTENTION! 

Catch up the cassette on the four corners. 

Don’t lift or move the unit through the ex

-

changer pipelines or the exhaust pipe con-

dense.

INSTALLATION

FIXING THE CASSETTE

Select a place of installation where there can be a clearance of a least 140 cm 
(

see  pic.  05

around  the  appliance.  Make  sure  that  the  installation  does  not 

interfere with existing electric wiring or plumbing.

-  To fix the panel only use the 4 supplied screws.
Do not use other kinds of screws or you could damage the condensate 
drain pan.

- Do not bend or narrow the unit piping.
- Do not remove the cap from the unit piping until immediately before connecting 
the pipes.
- To prevent deformation of the air intake grille, do not overtighten the screws.

B

A

C

D

>140

100 < H > 350

610 mm

300 mm

CHANGE OF AIR AND RECIRCULATION SYSTEM

- Side knockouts allow connection of a duct for fresh air intake and for conditio-

ning an adjacent room.

- Remove the external prepunched anti-condensate insulator and remove the 

knockout panels using a punch.

FRESH AIR RENEWAL

Remove the knockout holes and the insulation. The ducts may be in flexible po

-

lyester (with steel spiral core) or in corrugated aluminium lagged with anti-con-

densate material (fibreglass 12±25 mm thick). 

Upon completion of installation, 

surfaces that have not been insulated may be covered with anti-condensate 

insulating material (e.g.: 6 mm thick expanded neoprene).

Failure  to  comply  with  these  instructions  could  cause  dripping  due  to 
the  condensate;  the  manufacturer  cannot  be  held  responsible  for  any             
damage.

Summary of Contents for SOFT NC

























Reviews: