Edco TG-10 Operator'S Instruction Manual Download Page 13

E-TG10-I-0119

E-SPTS-I-0809

800-638-3326 • edcoinc.com • [email protected]

Page 13

800-638-3326 • edcoinc.com • [email protected]

EQUIPMENT DEVELOPMENT CO., INC.

SAFETY SYMBOLS

This symbol means that the machine is heavy if the machine needs to be lifted onto  or off of a truck, 

loading dock etc. that  proper technique or heavy duty lifting device should be used, personal injury could result.

(Yellow background with black pictogram and black outline)

This symbol means that there are sharp components and if feet/fingers/digits come in contact personal 

injury or death could result.

(Yellow background with black pictogram and black outline)

This symbol means that potential hazardous voltages are present and the equipment must be properly 

grounded and extreme caution should be taken. If for any reason maintenance or repair is needed, 

insure that voltage(s) are disconnected at the machine and the source unless (be cautious) voltage needs

to be present to troubleshoot the problem, then only qualified personal should work on “live” systems.

(Yellow background with black pictogram and black outline) 

This symbol means hazardous pressures are present. Caution should be exercised to prevent personal 

injury or damage to equipment. Face, eye and head protection should be used.

(Yellow background with black pictogram and black outline)

This symbol means explosive and hazardous vapors are present. Caution should be exercised to 

prevent personal injury to face and eyes. Breathing and personal protection should be used when 

servicing.

(Yellow background with black pictogram and black outline)

This symbol means that the guards must remain in place while the engine/motor on the machine is 

running because death or personal injury may result.

(Yellow background with black pictogram and black outline)

This symbol means that there are moving parts and if feet/fingers/digits are inserted under any edge of 

the cutter/grinder/saw cover while the engine/motor on the machine is running that personal injury and loss 

of foot/fingers/digits may result.

(Yellow background with black pictogram and black outline)

This symbol means the surface is HOT and that if fingers/digits/hands or any bare or unprotected skin comes

in contact with this surface or hot accessory, possible serious burns and personal injury may result.

(Yellow background with black pictogram and black outline)

This symbol means that this machine or product exposes the operator to chemicals, gases  or dust 

particles that are listed by the state of California as potentially causing cancer or reproductive harm. 

For more information go to: www. P65Warnings.ca.gov.

(Yellow background with black pictogram and black outline)

Summary of Contents for TG-10





















Reviews: