background image

5

EN

®

•  Never install damaged batteries.
•  Never install batteries of mixed types or of different ages in 

the transmitter.

•  Always remove exhausted batteries.

•  Always remove batteries before storing the transmitter.
•  Low battery power can result in loss of control of the RC 

vehicle.

TRANSMITTER BATTERY SAFETY PRECAUTIONS

REMOVING THE VEHICLE  BODY

A

B

INSTALLING THE BATTERY IN THE VEHICLE

1. Turn the battery clips (

A

) clockwise to remove the battery strap (

B

).

2. Install a fully charged battery.
3. Install the battery strap.
4. Turn the battery clips counterclockwise to secure the battery strap.
If desired, you can put foam blocks (ECX2015) in front of the battery 
so the weight of the battery increases rear traction or in back of the 
battery to increase steering response.

INSTALLING TRANSMITTER  BATTERIES

1. Slide the panel open on the bottom of the transmitter.
2. Obey the battery plus (+) and minus (-) diagram in the 

transmitter to install 4 AA batteries.

3. Slide the panel closed.

We recommend using only alkaline AA batteries in the 
transmitter, however, it is possible to use rechargeable NiMH 
batteries.

CAUTION:

 If using rechargeable batteries, charge only 

rechargeable batteries. Charging non-rechargeable 

batteries may cause the batteries to burst, resulting in injury to 
persons and/or damage to property.

Summary of Contents for Circuit ECX03020



















Reviews: