ECR International AMB-4 Application Manual Download Page 5

5

PN 240013666 REV. A [06/30/2022]

Installation shall be performed by a qualifed service 

agency�

This instruction shall be used in conjunction with each 

unit’s Installation, Operation and Maintanence Manual�

Installation shall conform to requirements of 

authority having jurisdiction or in absence of such 

requirements:

• 

United States

 

• National Fuel Gas Code, ANSI Z223�1/NFPA 54

• National Electrical Code, NFPA 70�

• Canada 

• Natural Gas and Propane Installation Code,       

CAN/CSA B149�1 and B149�2

• Canadian Electrical Code, Part I, Safety Standard 

for Electrical Installations, CSA C22�1

Where required by authority having  jurisdiction,  

installation shall conform to Standard for Controls 

and Safety Devices for Automatically Fired Boilers, 

ANSI/ASME CSD-1. 

Additional manual reset low water cutoff may be required.

Additional manual reset high temp limit may be required�

Massachusetts:

Boiler installation must conform to Commonwealth of 

Massachusetts code 248 CMR which includes but is not 

limited to installation by licensed plumber or gas fitter.

 WARNING

Fire, explosion, asphyxiation and electrical shock 

hazard�  Improper installation could result in 

death or serious injury�  Read this instruction 

and individual boiler’s Installation, Operation 

& Maintenance Manual and understand all 

requirements, including requirements of authority 

having jurisdiction, before beginning installation�  

Installation not complete until appliance operation 

verified per Installation, Operation & Maintenance 

Manual provided with each boiler��

!

  

CODES AND STANDARDS

Codes and Standards

 WARNING

Keep boiler area clear and free from 

combustible materials, gasoline and other 

flammable vapors and liquids.

DO NOT obstruct air openings to the boiler 

room�

Modification, substitution or elimination 

of factory equipped, supplied or specified 

components may result in personal injury or 

loss of life�

TO THE OWNER - Installation and service of 

this boiler must be performed by a qualified 

installer�

TO THE INSTALLER - Leave all instructions with 

boiler for future reference�

When this product is installed in the 

Commonwealth of Massachusetts the 

installation must be performed by a Licensed 

Plumber or Licensed Gas Fitter�

!

  

Summary of Contents for AMB-4

























Reviews: