4 .4 .1
DIL switch A: activate 2-wire photocell
▶
See figure
18
If the light path is interrupted during closure, the operator will
stop immediately and, after a short pause, travel until it
reaches the
OPEN
end-of-travel position.
ON
2-wire photocell
OFF
No safety device (delivery condition)
4 .4 .2
DIL switch B: without function
5
Radio
WARNING
Danger of injury during unwanted
door travel
Pressing a button on the hand
transmitter may result in undesired door
cycles and cause injury.
▶
Make sure that the hand
transmitters are kept away from
children and can only be used by
people who have been instructed
on how the remote-control door
functions!
▶
If the door has only one safety
feature, only operate the hand
transmitter if you are within sight of
the door!
▶
Only drive or pass through remote
control door systems when the door
is at a standstill!
▶
Never stay standing under the open
door.
▶
Please note that unwanted door
cycles may occur if a hand
transmitter button is accidentally
pressed (e.g. if stored in a
pocket / handbag).
CAUTION
Danger of injuries due to unintended door travel
Unwanted door travel may occur while teaching in the radio
system.
▶
Pay attention that no persons or objects are in the
door's travel range when teaching in the radio system.
ATTENTION
Functional disturbances caused by environmental
conditions
These conditions can impair function!
Protect the hand transmitter from the following conditions:
•
Direct sunlight (perm. ambient
temperature: – 20 °C to + 60 °C)
•
Moisture
•
Dust
•
If there is no separate garage entrance, perform all
teach-in processes, program changes and extensions
while standing in the garage.
•
After teaching-in or extending the radio system, perform
a function check.
•
Only use original components when extending the radio
system.
5 .1
Hand transmitter RSC 2
The hand transmitter works with a rolling code that changes
with each sending procedure. For this reason, it must be
taught in with the desired hand transmitter button on each
receiver that is to be controlled (see section 5.4 or the
receiver's operating instructions).
5 .1 .1
Control elements
▶
See figure
19
1
LED
2
Hand transmitter button
3
Battery
5 .1 .2
Inserting / changing the battery
▶
See figure
19
▶
Only use the battery type C2025, 3 V Li, and pay
attention to the correct polarity.
5 .1 .3
Hand transmitter LED signals
•
LED illuminated:
The hand transmitter is sending a radio code.
•
LED flashing:
The hand transmitter is transmitting, but the battery
charge is so low that it must be replaced soon.
•
No LED response:
The hand transmitter is not functioning.
– Check whether the battery has been inserted
correctly.
– Exchange the battery for a new one.
5 .2
Excerpt from the declaration of conformity
Conformity of the above-mentioned product with the
requirements of the directives according to article 3 of the
R & TTE directives 1999/5/EC was verified by compliance
with the following standards:
•
EN 300 220-2
•
EN 301 489-3
•
EN 50371
•
EN 60950-1
The original declaration of conformity can be requested from
the manufacturer.
5 .3
Integral radio receiver
The garage door operator is equipped with an integral radio
receiver. A maximum of 6 different hand transmitter buttons
can be taught in. If more are taught in, the first one will be
deleted without advance warning. All memory spaces are
empty in the delivery condition. They can only be taught in or
deleted when the operator is at a standstill.
5 .4
Teaching in hand transmitters
▶
See figure
20
1 .
Briefly press the
P
button on the operator cover.
The red LED will begin to flash, signalling readiness for
the teach-in process.
2 .
Hold the desired hand transmitter button down until the
LED begins flashing rapidly.
3 .
Release the hand transmitter button and press it again
within 15 seconds until the LED begins flashing very
rapidly.
TR10L003-B RE / 12.2013
27
ENGLISH
www.thegaragedoorcentre.co.uk
0800 525 442
www.thegaragedoorcentre.co.uk
