background image

Instruction manual for ECOSOFT Robust reverse osmosis system 

This manual is the intellectual property of, and copyrighted by ECOSOFT SPC LLC. Copying and reprinting is forbidden. © 2015 

 

2. SPECIFICATIONS AND COMPONENTS  

 

2.1 TECHNICAL SPECIFICATIONS 

 

Parameter 

Value 

Purified water flow rate 
@ 25 °C, 1000 mg/l total dissolved solids feed water 

55…60 l/h 

Feed water flow rate 

110…130 l/h 

Concentrate flow rate 

55…65 l/h 

Inlet water pressure 

2,0…5,0 bar* 

Operating pressure in membrane array 

5,0…7,0 bar 

Pressure in tank bladder (when used with pressure tank) 

0,4…0,6 bar 

Feed water temperature 

+4… +30 °C** 

Ambient air temperature 

+5…+40 °C** 

Connection to water mains 

½″ thread 

10  Overall dimensions, H × W × D (base model) 

420×220×425 
mm  

11  Weight (base model) 

6 kg 

12  Electrical rating 

230 V, 50 Hz 

13  Power consumption, max. 

80 W 

14  Ingress protection rating 

IP 54 

* If pressure of water in your system does not meet requirement, install a pressure booster pump to raise it. 

If water pressure exceeds the upper limit, install a pressure regulator before the Robust system. 

**  Using  the  Robust  system  with  feed  water  temperature  between  +20  and  +30  °С  produces  a  lower 

rejection  rate  and  higher  flow  rate,  which  yields  higher  TDS  of  purified  water.  Using  the  system  with  feed 

water above +30 °С is advised against. 

2.2 FEED WATER REQUIREMENTS* 

 

Parameter 

Value** 

pH 

6,5…8,5 

Total dissolved solids (TDS) 

< 1500 mg/l 


 

Hardness 
 

< 30 °dH (500 
mg CaCO /l) 


 

Residual chlorine 
 

< 0,5 mg/l 
 

Iron 

< 0,3 mg/l 

Manganese 

< 0,1 mg/l 


 

Chemical oxygen demand 
 

< 5 mg O

2

/l 

 


 

Total microbial count 
 

< 100 CFU/ml 
 


 

E. coli 

none 
 

* If feed water quality does not meet specified requirements, membrane and filter service life may decrease.  

**  If  aiming  to  purify  raw  water  (well  water/ground  water  etc),  it  is  recommended  to  carry  out  detailed 

water  analysis.  If  any  constituents  exceed  the  above  limitations,  it  is  advisable  to  install  a  special  filter 

upstream  of  your  reverse  osmosis  system.  Consult  professional  water  treatment  specialist  for  proper 

selection of an appropriate filter for your water. 

Summary of Contents for Robust





























Reviews: