background image

14).The instructions shall contain the substance of the following: If the supply
      cord is damaged, it must be replaced by the manufacturer, its service agent
     or similarly qualified persons in order to avoid a hazard.  
15). The water may drip from the discharge pipe of the pressure-relief device 
       and that this pipe must be left open to the atmosphere;the pressure-relief 
       device is to be operated regularly to remove lime deposits and to verify
       that it is not blocked; 
16). Transport using a forklift
        When transported by a fork lift, the unit must remain mounted on the pallet.
       The lifting rate should be kept to a minimum. Due to its top-heaviness, the 
       unit must be secured against tipping over.
       To prevent any damage, the unit must be placed on a level surface!
17). Manual transport
       For the manual transport, the wooden pallet can be used for bottom part.
       Using ropes or carrying straps, a second or third handling configuration is
       possible. With this type of handling, care must be taken that the max.
       Permissible inclination angle of 60 degree is not exceeded. 
        

Eposited and transportation

18)

1.PREFACE

Important warning:

Notes on environmental protection

    

  This product may be at the end of his life rather than the normal household
  waste will be sonderm at a collection point for the recycling of electrical 
  and electronic equipment will be delivered. The symbol on the product, 
  the instruction manual or packaging recalls. 
  The materials are recycled, according to their identification. With the reuse
  of recycling or other forms of recovery of waste afford a important 
  contribution to protect our environment. 
  Please ask at the municipal disposal of the competent authority.

60

2

CAUTION:

 

High center of gravity, low overturning moment!

Summary of Contents for ZR9W Series





















Reviews: