ecoObs Mini-batcorder 1.0 Quick Manual Download

Page: 8 / 17

SING

THE

INI

BATCORDER

Starting/Stopping the Mini-batcorder

Turning on the Mini-batcorder

Press the Start/Stop switch

All 3 LEDs are blinking green for three times, recording mode is activated.

The Mini-batcorder will run for 10 to 12 hours with LEDs activated. The run-

time is extended to ca. 40 hours by activating stealth mode.

Turning off the Mini-batcorder

Press and hold the Start/Stop switch for a couple of seconds

All 3 LEDs are blinking red for three times, the device is off now

Note: a single press on the Start/Stop button does only toggle

stealth mode. Only the 3x red flashing LEDs indicate a system shut-
down.

Stealth mode

Pressing the Start/Stop switch shortly while the Mini-batcorder is active will

toggle stealth mode.

Connecting with your computer

Please make sure that the Mini-batcoorder is stopped / switched off, before

you connect it with your computer. After connecting the LEDs flash green for

three times. When disconnecting, please make sure you eject the Mini-bat-

corder first from your operating system. Then, after disconnecting the USB

cable, the LEDs flash red 3 times. Only then the Mini-batcorder has itself

switched off again.

Summary of Contents for Mini-batcorder 1.0


















Search results

Summary of Contents for Mini-batcorder 1.0

Reviews:

Related manuals for Mini-batcorder 1.0

Brands by name

Popular brands

ecoObs Mini-batcorder 1.0, Quick Manual

Search results

Summary of Contents for Mini-batcorder 1.0

Reviews:

Related manuals for Mini-batcorder 1.0

Brands by name

Popular brands