background image

15

https://www.altonindustries.com

Check  the  electrical  connection  cables  for 
damage  regularly.  Make  sure  that  the 
connection  cable  does  not  hang  on  the 
power  network  during  the  inspection. 
Electrical connection cables must comply with 
the applicable VDE and DIN provisions. Only 
use  con-nection  cables  with  the  marking 
“H05VV-F”.

The printing of the type designation on the 
connec-tion cable is mandatory.

AC motor

The mains voltage must be 120V/60Hz
Extension  cables  up  to  25  m  in  length 
must have a cross section of at least 1,5 

2

2

mm  , above 25 m at least 2,5 mm
The mains connection is protected with a 
16 A slow-blow fuse.

Connections   and  repairs  of  electrical 
equipment  may  only  be  carried  out  by  an 
electrician.

Please  provide  the  following  information  in 
the event of any enquiries:

Type of current for the motor. 
Machine data - type plate. 
Motor data - type plate

10.CLEANING AND 
MAINTENANCE

Danger!

Always pull out the mains power plug before 
starting

 

any cleaning work.

Keep all safety devices, air vents and the 
motor housing free of dirt and dust as far 
as  possible.  Wipe  the  equipment  with  a 
clean cloth or blow it with compressed air 
at low pressure.
We recommend that you clean the device 
immediately each time you have finished 
using it.

Cleaning

Clean  the  equipment  regularly  with  a 
moist cloth and some soft soap. Do not 
use  cleaning  agents  or  solvents;  these 
could  attack  the  plastic  parts  of  the 
equipment. Ensure that no water can seep 
into the device. The ingress of water into 
an  electric  tool  increases  the  risk  of  an 
electric shock.

ln  case  of  excessive  sparking,

  have  the 

carbon

 

brushes checked only by a qualified 

electrician.

Carbon brushes

Danger!

 The carbon brushes should not be  

replaced

 

by  anyone  but  a  qualified 

electrician.

Maintenance

A  worn  out  or  damaged  cutting  unit 
should  be  re-placed  by  an  authorised 
expert.
Take  care  that  all  fastening  elements 
(screws,

 

nuts, etc. ) are firmly tightened, so 

that you can

 

work safely with the Electric 

Tiller.
Store the Electric Tiller in a dry place.
For  longer  life,  all  screw-fastened  parts, 
such  as

 

wheels  and  axles  should  be 

cleaned and subse-quently oiled.
Regular  servicing  of  the  implement  not 
only  se-cures  longer  endurance  and 
performance,  it  also

 

contributes  to  an 

accurate and simple dig up of

 

your bed.

At  the  end  of  the  season,  carry  out  a 
general  check

 

of  the  Electric  Tiller,  and 

remove all residue col-lected. Before the 
start  of  every  season,  it  is  ab-solutely 
necessary to check the state of the ma-
chine.Contact  our  Customer  Service  if 
repair work is necessary.

11.STORAGE

Store the device and its accessories in a dark, 
dry and frost-proof place that is inaccessible 
to   children.   The   optimum   storage 
temperature is between 5 and 30℃.

16

[email protected]

Store  the  electrical  tool  in  its  original 
packaging. 
Cover the electrical tool in order to protect it 
from

 

dust and moisture. Store the operating 

manual with

 

the electrical tool.

12.DISPOSAL AND RECYCLING

The  equipment  is  supplied  in  packaging  to 
prevent it from being damaged in transit. The 
raw materials in this packaging can be reused 
or  recycled.  The  equip-ment  and  its 
accessories  are  made  of  various  types  of 
material, such as metal and plastic. Defective 
components must be disposed of as special 
waste. Ask your dealer or your local council.

Old devices must not be disposed of with 
house-hold waste!

     

This symbol indicates that this product 

must  not  be  disposed  of  together  with 
domestic  waste  in  compliance  with  the 
Directive(2012/19/EU)  pertaining  to  waste 
electrical  and  electronic  equipment  (WEEE). 
This  product  must  be  disposed  of  at  a 
designated collection point. This can occur, for 
example, by handing it in at an author-ised 
collecting  point  for  the  recycling  of  waste 
elec-trical and electronic equipment. Improper 
handling  of  waste  equipment  may  have 
negative consequences for the environment 
and  human  health  due  to  po-tentially 
hazardous  substances  that  are  often  con-
tained in electrical and electronic equipment. 
By properly disposing of this product, you are 
also  con-tributing  to  the  effective  use  of 
natural resources. You can obtain information 
on  collection  points  for  waste  equipment 
from  your  municipal  administration,  public 
waste disposal authority, an authorised body 
for  the  disposal  of  waste  electrical  and 
electronic equipment or your waste disposal 
company.

13.SPARE-PART ORDERING

Please quote the following in your order for 
spare

 

parts:

Type of device
Article No. of deviceldent. No. of device
Spare Part No. of the required spare part

Service information

Please note that the following parts of this 
product

 

are  subject  to  normal  or  natural 

wear  and  that  the  fol-lowing  parts  are 
therefore   also   required   for   use   as

 

consumables.
wear parts*: Brush Assemblies, Blade Roller
*Not  necessarily  included  in  the  scope  of 
delivery!

Summary of Contents for ELG02














Reviews: