background image

Operator’s Manual  |  ECO 75  |  Turf Pros #1 Top dresser 

7

Before using the spreader for the first time, visually check the spreader which 

has been factory adjusted for immediate use, some minor adjustments may 

be necessary. We recommend the following startup procedure to ensure 

that the machine is properly adjusted before use.

Step 1.  

The spreader’s belts are new, so they may not adhere perfectly to the 

pulleys; they may slip when the machine is started for the first time until 

they are properly seated. Before loading the spreader with substrate, let 

it run empty for about 10 minutes to allow the belts to become seated 

properly on the pulleys.

Step  2.  

Fill the Hopper to 1/3 capacity (see Page 8, Step 1), then run the spreader 

until empty and refill to this level for the first 3 or 4 loads.

Step 3. 

Fill the Hopper to its maximum capacity (500 lbs / 227 kg) and begin using 

the spreader normally.

Step 4. 

After 1 hour of use, visually inspect the spreader. Vibrations combined with 

a heavy load may occasionally cause nuts and bolts to loosen. Tighten these 

when necessary.

Step 5. 

After 8 hours of use, inspect the nuts and bolts again and tighten if necessary.

If some pulleys do not run correctly after these trials, please refer to Ecolawn 

Application: Troubleshooting and Adjustments. 

USING THE 

ECOLAWN 

APPLICATOR 

FOR THE 

FIRST TIME

Summary of Contents for ECO 75





















Reviews: