background image

 

 

03.03.2021 Rev. 01 

18 

 
 

 

9.2.

 

Operating Principle 

 
The boiler can be set in 2 operations modes:-‘Summer’ (

DHW

 only), ’Winter’ (

CH & DHW

) ,  

 

9.2.1.

 

Winter Mode (CH & DHW) 

 

1.

 

Press the 

ON/OFF

 button (

K5

). Radiator and tap symbol will be displayed on the screen.

 

 

2.

 

CH water set temperature will be displayed on the screen when DHW is not needed.CH heating 

 

set  temperature  is  increases  by  pressing  (

K1

)  button,  and  decreases  by  pressing  (

K2

)  button.CH 

set  temperature  is  displayed  on  the  screen  when  pressed  to  these  buttons.  Flame  symbol  ( )  is 
displayed  on  the  screen  when  combi  is  started-up.  The  radiator  symbol  on  the  screen  will  be 
flashing when combi works at CH mode. 
 

3.

 

DHW  set  temperature  is  increased  by  pressing  to  (

K7

)  button,  and  decreased  by  pressing  (

K6

button. DHW set temperature is displayed on the screen when pressed to these buttons. When the 
DHW  is  needed,  combi  is  worked  on  DHW  mode  and  tap  symbol  will  be  flashing  when  combi 
works  at  DHW  mode.  Because  of  the  DHW  priority,  even  if  the  appliance  is  operating  at  CH, 
combi will switch to when DHW is needed.

 

 

 

 

9.2.2.

 

Summer Mode ( DHW only) 

 

1.

 

Press the 

ON/OFF

 button (

K5

) until the tap symbol will be displayed on the screen.

 

 

2.

 

DHW heating set temperature is increases by pressing (

K

7) button, and decreases by pressing 

(

K6

) button. DHW set temperature is displayed on the screen when pressed to these buttons. 

Combi will started at DHW mode when DHW is needed. 

 
 
 

9.3.

 

Boiler Frost Protection Mode 

 
When water outlet temperature decreased below 

5°C

, frost protection function of combi boiler operating 

system provides that burner starts up and increases water outlet temperature up to 

30°C

 
Frost protection mode works under the conditions below: 
 

1.

 

Combi Boiler electrical supply should be turned on. 

 

2.

 

Main gas valve on gas circuit should be opened. 

 

3.

 

Hydraulic water pressure should be adjusted properly. 

 
Combi boiler should not be blocked. 
 
 
 
 

Summary of Contents for WT-S 35
































Reviews: