background image

7

S-plan Wiring
PAW cylinders

 can be

fitted with all types of boilers and heat 

pumps operating using room and

cylinder thermostats.

Please follow upper diagram:

‘Wiring for Standard Heat Pump’.

Thermistor controlled Heat

Pumps/Boilers

Many popular Heat Pumps now

use a thermistor principle. A

thermistor temperature sensor is

supplied with the Heat Pump to

attach to the cylinder.

Temperature information is

relayed back to the Heat Pump

control system.

A Pocket is provided (see below

to secure the sensor on the

PAW cylinder. The

probe is run through a channel

from base of cylinder to the

immersion housing and housed

there in a pocket. The thermistor

cable should be secured using

the supplied clamps in the bottom

opening of the channel. A

motorised valve must be used in

accordance with Building

Regulation G3. This is wired from

the additional cylinder

thermostat, wired as high limit

stat. Please follow lower diagram:

‘Wiring for Thermistor Controlled

Heat Pump”

Using Additional Cylinder Thermostat

as high limit stat only:

- coil the grey temperature

probe wire inside additional

cylinder thermostat box and insert

black probe into thermostat pocket

of cylinder then turn dial on front to

number 5

Channel running

from base of cylinder

Pump 

flow

2-port valve

(supplied)

Zone valve

(not supplied)

Automatic 
bypass

Radiators/

UFH

HP/Boiler

Piping 
Diagram

Zone Valve (DHW)

 

(supplied)

1 2

2

3

1

T6360B

3

5

7

3

G/Y

L N E 4

G    Br   B

l

    O

L N E

L N E

Pump

1  2  3

2 3

2 3

2

2

3

1

V4043H

Cylinder 

Thermostat 

(supplied) Wired as 

high limit stat

Isolated Mains

 

Supply From 

Fused Spur 

Zone Valve (Htg)

 

(not supplied)

Room

 

thermostat

L  N E

6

9

2

3

1

V4043H

G  Br  B1   O    

G/Y

4

8

10

Wiring for Thermistor Controlled Heat Pump

1

 

2

 

Thermistor

Thermistor wire 
Connected to 
Heat Pump control 
system

1 2

2

3

1

T6360B

3

5

7

3

G/Y

L N E 4

G    Br  

  

B

l

    O

L N E

L N E

Heat Pump

Pump

1  2  3

2 3

2 3

2

2

3

1

V4043H

Cylinder 

Thermostat

 

(supplied)

Isolated Mains

 

Supply From 

Fused Spur 

Zone Valve (Htg)

 

(not supplied)

Room

 

thermostat

L  N E

6

9

2

3

1

V4043H

G  Br

   

B1   O    

G/Y

4

8

10

Wiring for Standard Heat pump

1

 

2

 

Zone Valve (DHW)

 

(supplied)

N L C NC NO

N L C NC NO

ST6400

Programmer

HW

ON

HTG

ON

ST6400

Programmer

HW

ON

HTG

ON

Heat pump differential controler

Summary of Contents for PAW-TD20C1E5-UK

















Reviews: