background image

 

14 

Warranty and Disclaimers 

 
 
 

WARRANTY 

 
The products described in this manual, with the exception of the UEGO sensor, are warranted 
to be free from defects in material and workmanship for a period of one year from the date of 
shipment to the buyer.  Within the one year warranty period, we shall at our option replace 
such items or reimburse the customer the original price of such items which are returned to us 
with shipping charges prepaid and which are determined by us to be defective.  This warranty 
does  not  apply  to  any  item  which  has  been  subjected  to  misuse,  negligence  or  accident;  or 
misapplied; or modified; or improperly installed. 
 
The  UEGO  sensor  is  considered  an  expendable  part  and  as  such  cannot  be  covered  by  a 
warranty.   
 
This  warranty  comprises  the  sole  and  entire  warranty  pertaining  to  the  items  provided 
hereunder.    Seller  makes  no  other  warranty,  guarantee,  or  representation  of  any  kind 
whatsoever.  All other warranties, including but not limited to merchantability and fitness for 
purpose, whether express, implied, or arising by operation of law, trade usage, or course of 
dealing are hereby disclaimed. 
 
The warranty is void if the control module is opened or the wiring harness is modified. 
 

LIMITATION OF REMEDY 

 
Seller's  liability  arising  from  or  in  any  way  connected  with  the  items  sold  and/or  services 
provided shall be limited exclusively to repair or replacement of the items sold or refund of 
the purchase price paid by buyer, at seller's sole option.  In no event shall seller be liable for 
any incidental, consequential or special damages of any kind or nature whatsoever, including 
but  not  limited  to  lost  profits  arising  from  or  in  any  way  connected  with  items  sold  and/or 
services  provided  to  buyer,  whether  alleged  to  arise  from  breach  of  contract,  express  or 
implied warranty, or in tort, including without limitation, negligence, failure to warn or strict 
liability.  In no event shall the company's liability to buyer arising out of or relating to the sale 
of  any  product  or  service  exceed the purchase price paid by buyer to the company for such 
product or service. 
 
 

PRODUCT CHANGES 

 
We reserve the right to discontinue a particular product or to make technical design changes 
at any time without notice. 
 

Summary of Contents for F/A1000



























Reviews: