Eclipse CD5435 Owner'S Manual Download

Page: 71 / 128

How to operate the tuner

Changing the radio band location

The location for the radio bands used between the North American region
and the Asia/Australia/Latin region can be switched. The default setting is
USA (North America).

Check that the deck is in standby mode.

Press and hold button [3], then the [FM AM] button, and
hold both for more than three seconds.

The radio band switches

in the order shown below

each time the

buttons are pressed.

After this, the broadcast stations will be searched for
automatically and stored in buttons [1] to [6].

When an optional HD Radio tuner unit is connected, radio band
location is set to USA. Other radio band locations are unavailable.
(U.S.A. only)

[FM AM] button Button [3]

USA

ASIA

AUS

LATIN

CD5435.book 71 ページ２００４年１２月１１日　土曜日　午後５時２９分

Summary of Contents for CD5435

































































































































Search results

Summary of Contents for CD5435

Reviews:

Related manuals for CD5435

Brands by name

Popular brands

Eclipse CD5435, Owner'S Manual

Search results

Summary of Contents for CD5435

Reviews:

Related manuals for CD5435

Brands by name

Popular brands