background image

Page 13

Installation Considerations

• Follow local, state, and 

National Electric Code

 requirements for 

grounding the over-the-air antenna.

• RG-6 coaxial cable is preferred for the 

O

VER

 

THE

 A

IR

 A

NTENNA

 

I

N

 connection. If you are diplexing the 

O

VER

 

THE

 A

IR

 A

NTENNA

 

I

N

 and 

S

ATELLITE

 I

N

 cables, RG-6 cable must be used.

• You cannot use a diplexer to combine the 

O

VER

 

THE

 A

IR

 

A

NTENNA

 I

N

 and 

S

ATELLITE

 I

N

 cables if using an amplified 

antenna.

• Reception of digital over-the-air broadcasts is outside of the 

control of DISH Network. If you have questions about over-the-
air broadcasts, contact the broadcaster, not DISH Network. 

Digital Transition Consideration

Although all full-power over-the-air stations are transitioning to digital-
only broadcasts beginning February 17, 2009, there will be some 
broadcasters who will continue using analog signals after this date. 
Because the OTA Module includes digital-only tuners, stations that are 
still broadcasting analog signals cannot be received using this module.

OTA Module.book  Page 13  Thursday, July 3, 2008  4:35 PM

Summary of Contents for MT2 OTA



















Reviews: