3
Installation Guide
tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast)
email - [email protected] (US)
email - [email protected] (Europe)
2
Installation Guide
tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast)
email - [email protected] (US)
email - [email protected] (Europe)
Fitting Instructions
PS-RBP/PS-RDIS
ParkAlert Rear Sensor System
with Buzzer or Display
PS-RBP/PS-RDIS
ParkAlert Rear Sensor System
with Buzzer or Display
Introduction
Box Contents
Key Features
u
Triangulation technology
u
2 or 4 sensor installation
u
Low profile, paintable sensors
u
Wide detection angle with minimal blind area
u
OE sounding tone
u
Dip switch settings for detection zones
u
Self-diagnostic mode at startup
u
Compatible with optional display
(P/N: PA-DISPLAY)
u
4 Bumper Mount Sensors
with 18” Pigtail
u
4 Black Rubber Seals
u
4 6° Sensor Sleeves
u
4 12° Sensor Sleeves
u
Control Module
u
Speaker with Volume Control
u
Power Harness
u
22.5mm Hole Saw
u
Accessory Pack
u
Measuring Tape
u
User Manual
u
Warranty Card
Congratulations on purchasing EchoMaster PRO parking sensors. This ultrasonic
detection system is designed to assist in the avoidance of obstacles while reversing.
Disclaimer:
EchoMaster® is strictly a driver assistance device, and should not be relied upon as a substitute for safe driving
practices. Use common sense when parking and always follow recommended safe driving guidelines from your local,
State and County Department of Motor Vehicles regarding parking procedures. To help prevent accidents, always
use caution when parking, looking visually to ensure your path is clear. Keep speeds under three miles per hour. The
owner shall not be entitled to recover from the Company, its successors or assignees, incidental and consequential
damages, such as personal injury, loss of income, loss of time, loss of profits, loss of vehicle use or property damage.
No employee, agent or representative of the Company of the Selling Retailer may modify, alter or extend this Warranty
in any way. This Warranty gives you specific legal rights. You may also have other rights under this Warranty which
may vary from state to state.
Note: Under no circumstances should you attempt to open the control box or any other component. Doing so will void
all manufacturer’s warranties.
This manual covers products:
PS-RBP-B
(ParkAlert Rear Sensor System with Buzzer - Gloss Black sensors)
PS-RBP-M
(ParkAlert Rear Sensor System with Buzzer - Matte Black sensors)
PS-RBP-S
(ParkAlert Rear Sensor System with Buzzer - Silver sensors)
PS-RBP-W
(ParkAlert Rear Sensor System with Buzzer - White sensors)
PS-RDIS-B
(ParkAlert Rear Sensor System with Display - Gloss Black sensors)
PS-RDIS-M
(ParkAlert Rear Sensor System with Display - Matte Black sensors)
PS-RDIS-S
(ParkAlert Rear Sensor System with Display - Silver sensors)
PS-RDIS-W
(ParkAlert Rear Sensor System with Display - White sensors)
Recommended Tools
for Installation
u
High torque drill, use slow speed
(approx 400 rpm)
u
Grease Pencil and Center Punch
for marking drill point
u
1/8” carbide tipped drill bit for
starting pilot hole
u
Hole Saw 22.5mm (Included)
u
Pliers, Crimpers & Soldering Iron
u
Multi-Meter
u
Zinc Galvanizer or a rust inhibitor
for metal (OPT P/N: EMZ)
u
Safety goggles
u
Angle Gauge Sleeve Selector (OPT P/N: SP1022)
u
Measuring Tape
Optional Tools
u
Panel tool (for situations requiring plastic, inner
panels to be removed)
u
Phillips head tip for drill
u
Wire pulling tool (for routing wires)/ Fishing tool
u
Semi-circular metal file (for smoothing hole
edges when necessary)- DO NOT use fingers
to test holes for burrs or smoothness.
EDGES ARE SHARP!!!
Determining Sensor Position: Measure Twice, Cut Once!
Inspect behind the bumper in the approximate mounting area to check for any
possible obstructions.
A proper installation will take into consideration two factors:
(1) Placement:
height and distance either side of bumper center.
(2) Angle:
accurate detection depends on the correct sensor angle.
The sensors need a 1” clearance space behind the bumper to be completely inserted.
Some bumpers have an outside cover or fascia and a metal backing. You may have to
drill through both layers to ensure you have enough clearance in order to fit the
sensors. Other bumpers require some removal of foam backing.
CAUTION: Be careful of hot engine parts and/or sharp edges under bumper.
DO NOT INSTALL SENSORS ABOVE EXHAUST PIPE.
Doing so may cause false alerts.
