background image

Echoflex Installation Guide

Ceiling Vacancy-Occupancy Sensor

To replace the battery:

1. Use your fingers to remove the cover, flexing it gently to release the

tabs that hold it in place. If you have difficulty, consider inserting a
small flatblade screwdriver under a release tab.

2. Use your finger to remove the old battery from the holder. Insert a

new battery with the + positive side facing up and press in place.

3. Replace the cover and press in place.

Tests and Settings

Use the

[Teach]

button and color LEDs to navigate the Tests and Settings

Menu. Remove the cover to access the

[Teach]

button located beside the

battery clip. The LEDs display through the front lens.

Note:

A battery is required to run tests or change settings. If you

cannot access the LED blink menu, replace the battery. See

Battery

Power on page 5

for installation instructions.

Light Level Test

(green LED)

Range Confirmation

(blue LED)

Walk Test

(red LED)

Sensor Setting

(red and blue LEDs)

LED Display

(green and red LEDs)

The menu times out after two minutes of inactivity.

Light Level Test

The Light Level Test quantifies the amount of energy produced by the
solar cells and confirms a good installation location.

1. Press and hold the

[Teach]

button until the green LED appears.

Release the button to enter the menu and display the first item,
blinking green LED.

2. Press and hold the

[Teach]

button again until the green LED stops

blinking. The green LED then repeats a number of blinks according to
the detected light level. If you move the sensor, it reevalutes the light
level every two seconds.

Blinks

Lux (Footcandles)

Charge Level

1

< 40 (< 3.7)

Not sustainable

2

40–65 (3.8–6)

PIR operational only

3

> 65 (> 6)

Dual-tech operational

The test repeats every two seconds and runs for 100 seconds. To exit
before the time-out, press and hold the

[Teach]

button for 10 seconds.

Ceiling Vacancy-Occupancy Sensor

Page 6 of 12

Echoflex

Summary of Contents for RVS-A-xW Series













Reviews: