background image

- 11 -

TRIMMING

The nylon line will allow you to trim along walls and
fence lines. Always try to trim from right to left, walking
behind the unit and parallel to the wall or fence, thus
deflecting debris away from the operator.

EDGING

1. The nylon line is intended only to cut grass and

should not be used to cut a normal edging trench
along stone or concrete driveway etc.

2. Tilt the unit vertically as illsutrated and use only

the line tip to remove unwanted growth.

MOWING

The nylon line will effectively mow large areas of
heavy grass and/or weeds. Use the standard 12.5
- 15 cm ( 5 - 6 inch) of line and operate at full
throttle.

When mowing cultivated areas such as lawns hold
the cutter head pararell to the gound to avoid
scalping.

SCALPING

1. The cleaning of weeds and grass right down to

the earth can be accomplished very easily with
the nylon line.

2. Scalping around trees and brushes is particularly

effective, but care should be exercised not to bruise
the bark of young and sensitive growth.

3. In flower beds, always remenber that the nylon

line will cut in a complete circle to avoid cutting
flowers instead of weeds.

TREE

SWEEPING

1. Sweeping grass and other debris from a hard

surface can be done very quickly.

Summary of Contents for SRM-3800 TYPE1-E






















Reviews: