![background image](http://html1.mh-extra.com/html/echo/srm-335es/srm-335es_operators-manual_532846020.webp)
18
Trimming operation
Using shoulder harness
Always mount the trimmer correctly using the shoulder har-
ness.
Buckle waist belt. Belt should be snug.
Attach product to harness.
Place shoulder harness over both shoulders and adjust
straps so the connecting point latches as shown.
Check for correct adjustment by moving cutting attachment
along ground.
Re-adjust position of suspension point if necessary.
The shoulder harness is fitted with an emergency release
function. In the event of a fire or other emergency, pull the
quick release pin (A) up to release the product from your
body.
Basic trimming operation with nylon line cutting head
Trimming
This is feeding the trimmer carefully into the material you wish
to cut. Tilt the head slightly to direct the debris away from you.
If cutting up to a barrier such as a fence, wall or tree, approach
from an angle where any debris ricocheting off the barrier will
fly away from you.
Move the nylon line cutting head slowly until the grass is cut
right up to the barrier, but do not jam (overfeed) the line into
the barrier. If trimming up wire mesh or chain link fencing, be
careful to feed only up to the wire. If you go too far, the line will
snap off around the wire.
Trimming can be done to cut through weed stems one at a
time. Place the nylon line cutting head near the bottom of the
weed never high up, which could cause the weed to chatter
and catch the line. Rather than cut the weed right through, just
use the very end of the line to wear through the stem slowly.
1. Angle
to
wall
2. Debris
3. Knife
side
raised
4. Angle
to
ground
Scything
This is the cutting or mowing of large grassy areas by sweep-
ing or swinging the trimmer in a level arc. Use a smooth, easy
motion. Do not try to hack or chop down the grass. Tilt the ny-
lon line cutting head to direct the debris away from you on the
scything stroke. Then return without cutting grass for another
stroke. If you are well protected and do not care whether some
debris is thrown in your direction, you may scythe in both di-
rections.
WARNING
Serious injury may result from the improper use of cutting attachment. Read and comply with all safety instructions
listed in this manual.
Use only cutting attachments recommended by YAMABIKO CORPORATION.
Excessive nylon line beyond cut off knife could fly off when the nylon line cutting head starts rotating after adjust-
ment of nylon line length.
Failure to do so could lead to an accident or serious injury.
Summary of Contents for SRM-335ES
