background image

SRM-266U

MAINTENANCE

X7502026204

31

© 04/2014 ECHO Inc.

When the wear indicators located at the bottom of the 
Speed-Feed® head are worn smooth, or if holes appear, 
replacement of the cover or the entire Speed-Feed® head is 
required.

Sharpening Metal Blades

Three styles of metal blades are approved for use on the ECHO 
Brush Cutter. The 8-tooth blade can be sharpened during 
normal maintenance. The clearing blade and 80 tooth blade 
require professional service.

Before sharpening, CLOSELY inspect blade for cracks (look at 
the bottom of each tooth and the center mounting hole closely), 
missing teeth and bending. If ANY of these problems are 
discovered, replace the blade.

When sharpening a blade, always remove the same amount of 
materials from each tooth to maintain balance. A blade that is not balanced will cause unsafe handling due 
to vibration and can result in blade failure.

1. File each tooth at a 30 degree angle a specific number of 

times, eg. 4 strokes per tooth. Work your way around the 
blade until all teeth are sharp.

2. DO NOT file the ‘gullet’ (radius) of the tooth with the flat file. 

The radius must remain. A sharp corner will lead to a crack 
and blade failure.

If an electric grinder is used, use care not to overheat teeth, do 
not allow tips/tooth to glow red or turn blue. DO NOT place 
blade in cooling water. This will change the temper of the blade and could result in blade failure.

3. After sharpening teeth, check each tooth radius for evidence 

of a square (sharp) corner. Use the round (rat tail) file to 
renew the radius.

Wear Indicators

Summary of Contents for SRM-266U









































Reviews: