background image

22

R + M

2

FUEL

Fuel Requirements

Gasoline -

 Use 89 Octane [       ] gasoline or gasohol known to be good

quality.  Gasohol may contain up to 10% Ethyl (grain) alcohol or 15%
MTBE (methyl tertiary-butyl ether). Gasohol containing methyl (wood)
alcohol is 

NOT

 approved.

Two Stroke Oil

 - A two-stroke engine oil meeting  ISO-L-EGD Standard

(ISO/CD 13738), must be used. Echo brand Premium 50:1 oil meets this

standard. Engine problems due to inadequate lubrication caused by

failure to use an ISO-L-EGD approved oil, such as Echo Premium 50:1

Two-stroke Oil, will void the two-stroke engine warranty. 

 

(Emission

related parts  only are covered for two years, regardless of two-stroke

oil used, per the statement listed in the EPA Phase I/California Emission
Defect Warranty Explanation.)

Mixing -

 Follow directions on the oil container.

Handling Fuel

WARNING              DANGER

Fuel is 

VERY

 flammable. Use extreme care when mixing, storing or

handling or serious personal injury may result.

• Use an approved fuel container.

• DO NOT smoke near fuel.

• DO NOT allow flames or sparks near fuel.

• Fuel tanks/cans may be under pressure. Always loosen fuel caps

slowly allowing pressure to equalize.

• NEVER refuel a unit when the engine is HOT!

• NEVER refuel a unit with the engine running.

• DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors

over bare ground.

• Securely tighten fuel cap after refueling.

• Inspect for fuel leakage. If fuel leakage is found, do not start or

operate unit until leakage is repaired.

After Refueling;

• Wipe any spilled fuel from the unit.
• Move at lease 3M (10 ft.) from refueling location before starting the

engine.

After use;

• DO NOT store a unit with fuel in its tank. Leaks can occur. Return

unused fuel to an approved fuel storage container.

Storage -

 Fuel storage laws vary by  locality. Contact your local

government for the laws affecting your area. As a precaution, store fuel
in an approved, air tight container. Store in a well ventilated, unoccu-
pied building, away from sparks and flames. Do not store fuel longer
than 30 days.

Summary of Contents for SRM-2400 TYPE 1E - 09-99





































Reviews: