background image

G

RASS

 T

RIMMER

/B

RUSH

 C

UTTER

O

PERATOR

'

S

 M

ANUAL

21

SPARK

 

PLUG

Level 2.

Tools required:

T-Wrench, feeler gauge, soft metal brush

Parts Required: REPOWER

TM

 Tune-Up Kit P/N 90074C

IMPORTANT
Use only NGK BPM-8Y spark plug (BPMR-8Y in Canada)
otherwise severe engine damage may occur.

1. Remove spark plug and check for fouling, worn and rounded

center electrode.

2. Clean the plug or replace with a new one.  DO NOT sand blast to

clean. Remaining sand will damage engine.

3. Adjust spark plug gap by bending outer electrode.

4. Tighten spark plug to 150-170 kg/cm (130-150 in. lb.).

COOLING

 

SYSTEMS

 

CLEANING

Level 2.

Tools required:

Cross-head screwdriver, 3 and 4 mm hex wrench,
25 - 50mm (1 - 2 in.) cleaning brush.

Parts Required: None if you are careful.

IMPORTANT
To maintain proper engine operating temperatures, cooling air must
pass freely through the cylinder fin area. This flow of air carries
combustion heat away from the engine.

Overheating and engine seizure can occur when:
• Air intakes are blocked, preventing cooling air from reaching the

cylinder.

• Dust and grass build up on the outside of the cylinder. This build up

insulates the engine and prevents the heat from leaving.

Removal of cooling passage blockages or cleaning of cooling fins is
considered “Normal Maintenance.”  Any failure attributed to lack of
maintenance is not warranted.

0.65 mm

(0.026 in.)

Summary of Contents for SRM-210 - 12-06

































Reviews: