background image

16

8 Tooth Weed/Grass Blade (P/N 69600120331) is designed for grass,
garden debris and thick weeds.  DO NOT use this blade for brush or
heavy woody growth, 19 mm (3/4 in.) diameter or larger.

80 Tooth Brush Blade (P/N 69500120331) is designed for cutting brush
and woody growth up to 64 mm  (2-1/2 in.) diameter.

22 Tooth Clearing Blade (99944200130) is designed for dense thickets
and saplings up to 64 mm (2-1/2 in.) diameter.

Use Shoulder/Waist Harness (P/N 99944200200) Use of the  Shoulder/
Waist Harness is recommended for ALL Trimmer/Brush Cutter use. The
Shoulder/Waist Harness suspends the trimmer from the operator's
shoulder and reduces operator fatigue.

The restrictive harness enhances operator safety by reducing the
possibility of blade contact with the operator's hands and feet.

Choosing the Correct Blade

Plastic/Nylon Blades may be used where ever the nylon line head
is used.  DO NOT use this blade for heavy weeds or brush!

WARNING  

  DANGER

The type of Blade used MUST be matched to the type and size of material cut.  An improper or dull blade can cause
serious personal injury.  Blades MUST be sharp.  Dull blades increase the chance of kick out and injury to yourself
and bystanders.

Summary of Contents for RM-210SB

































Reviews: