manualshive.com logo in svg

Echo Quickvent QV-8000 Type 1, Instruction Manual, Page: 21 / 30

Share
Download
Echo Quickvent QV-8000 Type 1 Instruction Manual Download Page 21

19

QV-8000 TYPE1-E

Inspect and adjust chain brake
(After Each Use)

   CAUTION

If proper brake adjustment cannot be
obtained, take your unit to your authorized
ECHO servicing dealer before further use of
system.

1. Remove the sprocket guard.

2. Remove the bar and chain.

3. Remove the guide bar plate and cartridge from

the sprocket guard.

4. Inspect clutch drum and brake band for wear

and replace if necessary.

5. Turn the tension screw clockwise to increase

tension or counterclockwise to decrease
tension.

6. Reinstall the cartridge and guide bar plate in

the sprocket guard.

7. Reinstall bar and chain.

8. Install sprocket guard.

9. Set chain tension. See “Adjust chain tension” in

this section.

10. Activate the chain brake with the guard and

with a gloved hand try to pull the chain along
the top of the guide bar.

11. Move chain with hand guard in unbraked

position.

12. Start the engine.

13. Depress throttle fully and activate the brake.

MAINTENANCE

WHAT HAPPENED?

Chain Moves.

Chain Does Not Move.

Adjusting screw

Brake lever

Sprocket guard

Brake band

Direction to tension

WHAT DO YOU DO?

Increase Tension.

Go to Next Step.

WHAT HAPPENED?

Brake Spring Rubs on
Drum.

Chain Rotates Smoothly
without Drag.

WHAT DO YOU DO?

Decrease Tension and
Go to next Step.

Go to next Step.

WHAT HAPPENED?

Chain Slows to a Stop.

Brake Spring Rubs on
Drum.

Chain Stops
Immediately.

WHAT DO YOU DO?

Increase Tension.

Decrease Tension.

Brake is Adjusted
Properly.

NOTE

• Move the chain brake lever (Front hand guard)

fully rearward to remove or install the clutch
cover to chain saw.

• Clean parts as you remove them.

Summary of Contents for Quickvent QV-8000 Type 1































Reviews:

No comments