Echo Quickvent QV-8000 Type 1 Instruction Manual Download Page 13 | Manualshive

Page: 13 / 30

Echo Quickvent QV-8000 Type 1 Instruction Manual Download Page 13

11

QV-8000 TYPE1-E

Running

• When engine starts, keep idling for a few minutes.

• Set the brake lever in the unlocked position before

starting to cut.

• Pull throttle trigger gradually and increase

revolution of the engine.

• The chain starts running when the engine reaches

3800 r/min approximately.

• Confirm proper acceleration and lubrication of

chain and bar.

• Give several strokes to manual oiler button to

confirm extra lubrication.

• Do not run the engine at high speed

unnecessarily.

• Be sure that saw chain stops moving when throttle

trigger is released.

OPERATION (Pre-Ventilation Procedures)

Start/Run

Ignition switch

Lock chain brake

Unlock chain brake

When the engine is warm

CAUTION

Make sure the bar and chain are free from
any obstruction when starting the chain saw.

• Move chain brake lever fully forward to lock chain

brake before starting.

• Confirm there is fuel and chain oil in the tanks.

• Move ignition switch to “RUN” position.

• Securely hold the chain saw as shown and pull

starter handle.

• Choke may be used if necessary, but be sure to

push it back on first firing sound.

• After starting the engine, pull front hand guard

towards the operator immediately. (Chain brake
unlocked position)

Manual oiler

Starter handle

«
...
11
12
13
14
15
...
»

Summary of Contents for Quickvent QV-8000 Type 1































Reviews:

No comments