background image

6

An Emission Control Label is located on the engine.  (This is an EXAMPLE ONLY, information on label varies by engine
FAMILY).

PRODUCT  EMISSION  DURABILITY

The 300 hour emission durability compliance period is the time span selected by the manufacturer certifying the
engine emissions output meets applicable emissions regulations, provided that approved maintenance procedures are
followed as listed in the Maintenance Section of this manual.

EQUIPMENT

WARNING   

   DANGER

Use only ECHO approved attachments for Pro Attachment Series

TM

 models. Serious injury may result from the use of

a non-approved attachment combination. Read and comply with all safety instructions listed in this manual and
attachment manual.

NOTE
ECHO, INC. will not be responsible for the failure of cutting devices, attachments, or accessories which have not
been tested and approved by ECHO for use with this Pro Attachment Series

TM

.

• Check unit for loose/missing nuts, bolts and screws. Tightenand/or replace as needed.

• Inspect fuel lines, tank and area around carburetor for fuel leaks.  DO NOT operate unit if leaks are found.

• Inspect guards for damage and ensure that they are securely in place. Replace if guard is damaged or missing.

• Check that the attachment is firmly attached and in safe operating condition.

E

MISSION

 C

ONTROL

EPA Phase 2 / C.A.R.B. TIER III

The emission control system for the engine is EM/TWC (Engine Modification and 3-way Catalyst) and for the fuel tank
the Control System is EVAP (Evaporative Emissions). Evaporative emission may be applicable to California models only.

IMPORTANT ENGINE INFORMATION

ENGINE FAMILY:   7EHXS.0254KA  DISPLACEMENT:  25.4 

CC

EMISSION COMPLIANCE PERIOD : 300 HRS.

THIS ENGINE MEETS U.S. EPA PHASE 2 EMISSION

REGULATIONS FOR SMALL NONROAD ENGINES.  REFER TO

OWNER'S MANUAL FOR MAINTENANCE SPECIFICATIONS

AND ADJUSTMENTS.

IMPORTANT ENGINE INFORMATION

ENGINE FAMILY:    7EHXS.0254KA  DISPLACEMENT:  25.4 

CC

EMISSION COMPLIANCE PERIOD : 300 HRS.

THIS ENGINE MEETS U.S. EPA PH2 EXH AND 2007 AND

LATER CALIFORNIA EXH AND EVAP EMISSION REGULA-

TIONS FOR S.O.R.E.  REFER TO OWNER'S MANUAL FOR

MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.

Summary of Contents for PAS-260 PRO - 12-06

























Reviews: