Echo PAS-260 PRO - 09-05 Operator'S Manual Download Page 23

Page: 23 / 24

TTACHMENT

ERIES

PERATOR

ANUAL

PECIFICATIONS

MODEL ----------------------------------------------------- PAS-260

Unit Length ------------------------------------------------- 1025 mm (40.4 in.)

Width -------------------------------------------------------- 250 mm (9.84 in.)

Height ------------------------------------------------------- 250 mm (9.84 in.)

Weight (dry) ------------------------------------------------ 4.0 kg (8.82 lb.)

Engine Type ------------------------------------------------ Air cooled, two-stroke, single cylinder gasoline engine

Bore ---------------------------------------------------------- 34.0 mm (1.34 in.)

Stroke -------------------------------------------------------- 28.0 mm (1.10 in.)

Displacement ----------------------------------------------- 25.4 cc (1.55 cu. in.)

Exhaust ------------------------------------------------------ Spark Arrestor Muffler / with catalyst

Carburetor -------------------------------------------------- Walbro w/purge pump

Ignition System -------------------------------------------- CDI (capacitor discharge ignition)

Spark Plug -------------------------------------------------- NGK BPM-8Y Gap 0.65 mm (0.026 in.)

Fuel ---------------------------------------------------------- Mixed (Gasoline and Two-stroke Oil)

Fuel/Oil Ratio ----------------------------------------------- 50:1 two-stroke air cooled engine oil

Gasoline ----------------------------------------------------- 89 Octane unleaded. DO NOT use fuel containing methyl alcohol,

more than 10% ethyl alcohol or 15% MTBE.

Oil ------------------------------------------------------------ Power Blend

Premium Universal 2-Stroke Oil

Fuel Tank Capacity ---------------------------------------- 0.58 lit. (19.6 US fl. oz.)

Starter System ---------------------------------------------- Automatic Rewind Starter

Clutch ------------------------------------------------------- Centrifugal Type

Drive Shaft -------------------------------------------------- 6.35 mm (1/4 in.) flexible shaft

Idle Speed --------------------------------------------------- 2,400 - 3,200 rpm

Wide Open Throttle Speed (W.O.T.)

with Nylon Line Head ------------------------------------- 8,500 - 10,500 rpm

Wide Open Throttle Speed (W.O.T.)

with Blade --------------------------------------------------- 9,000 - 11,000 rpm

RECOMMENDED

OPTIONAL

ATTACHMENTS

• PAS Edger

Model 99944200470

• PAS Cultivator

Model 99944200510

• PAS Trimmer

Model 99944200540

• PAS Hedge Clipper

Model 99944200480

• PAS Power Pruner

Model 99944200530

• PAS Pro Paddle

Model 99944200620

• PAS Pro Sweep

Model 99944200550

• PAS Pro Thatch

Model 99944200560

• PAS Articulating Hedge Clipper

Model 99944200590

• PAS Rapid Loader

Model 99944200610

• PAS Brush Cutter

Model 99944200600

Summary of Contents for PAS-260 PRO - 09-05

























Search results

Summary of Contents for PAS-260 PRO - 09-05

Reviews:

Related manuals for PAS-260 PRO - 09-05

Brands by name

Popular brands

Echo PAS-260 PRO - 09-05, Operator'S Manual

Search results

Summary of Contents for PAS-260 PRO - 09-05

Reviews:

Related manuals for PAS-260 PRO - 09-05

Brands by name

Popular brands