background image

1

INTRODUCTION

We are constantly working on technical im-
provement of our products. For this reason, 
technical data, equipment and design are 
subject to change without notice. All speci-
fications and directions in this SERVICE 
DATA are based on the latest products infor-
mation available at the time of publication.

1

1

2

-23

A

-00

HC-331ES, HC-341ES

CONTENTS

 

page

1 SERVICE INFORMATION

 .............................. 2

1-1 Speci

fi

 cation ............................................... 2 

1-2 Technical data ............................................. 3
1-3 Torque limits................................................ 4
1-4  Special repairing materials ......................... 4
1-5 Service limits............................................... 5
1-6 Special tools ............................................... 6

2 CARBURETTOR ADJUSTMENT PROCEDURE

 ...7

2-1  General adjusting rules ............................... 7
2-2  Presetting Idle adjust screw, Idle mixture 
needle and Hi speed mixture needle  .................... 7
2-3 Adjusting carburettor................................... 8 

Reference No.

 

1

2

-23

A

-00

I S S U E D :     2 0 0 8 0 4

SERVICE DATA

HEDGE TRIMMER

HC-331ES
HC-341ES

(Serial number : 36000001 and after)

Summary of Contents for HC-331ES









Reviews: