background image

10

S

PECIFICATIONS

MODEL ------------------------------------------ GT-200R

Length -------------------------------------------- 1400 mm (55.1 in.)

Width --------------------------------------------- 310 mm (12.2 in.)

Height -------------------------------------------- 385 mm (15.2 in.)

Weight (dry) w/Cutter Head ------------------- 4.1 kg (9.04 lb.)

Engine Type ------------------------------------- Air cooled, two-stroke, single cylinder gasoline engine

Bore ----------------------------------------------- 32.2 mm (1.27 in.)

Stroke --------------------------------------------- 26.0 mm (1.02 in.)

Displacement ------------------------------------ 21.2 cc (1.29 cu. in.)

Exhaust System --------------------------------- Spark Arrestor Muffler

Carburetor --------------------------------------- Zama diaphragm model RB w/primer

Ignition System --------------------------------- Flywheel magneto, capacitor discharge

Spark Plug --------------------------------------- NGK  BPMR-8Y   Gap 0.65 mm (0.026 in.)

Fuel ----------------------------------------------- Mixed (Gasoline and Two-stroke Oil)

Fuel/Oil Ratio ------------------------------------ 50:1 two-stroke air cooled engine oil

Gasoline ------------------------------------------ 89 Octane unleaded. DO NOT use fuel containing methyl alcohol, more than

10% ethyl alcohol or 15% MTBE.

Oil ------------------------------------------------- Power Blend 

TM

 Premium Universal 2-Stroke Oil

Fuel Tank Capacity ----------------------------- 0.45 lit. (15.2 US fl. oz.)

Starter System ----------------------------------- i30 Automatic Rewind Starter

Clutch -------------------------------------------- Centrifugal Type

Drive Shaft --------------------------------------- 1/4 in.  Flex Shaft

Rotating Direction ------------------------------ Clockwise viewed from top

Cutter Head -------------------------------------- Nylon line head (2-line) with .080 Line capacity 203 mm (8 in.)

Handle -------------------------------------------- Left - D-Loop, Right - Grip

Shoulder Harness ------------------------------- Optional  P/N 99944200201

Idle Speed (RPM) ------------------------------- 2,400 - 3,200 RPM

Wide Open Throttle Speed (W.O.T.)

 with Nylon Line Head (RPM) ----------------- 6,800 - 8,800 RPM

IMPORTANT
This spark ignition system complies with Canadian ICES-002.

Summary of Contents for GT-200R - SERIAL NUMBER 07003101-07999999

























Reviews: