background image

19

CS-355T

STOP

Control lever

Throttle trigger

Unlock chain brake

RUNNING

  

  warning  

The saw chain should not move at idle, otherwise 

serious personal injury may result.

nOTE

If saw chain moves adjust carburetor according to 

“Carburetor Adjustment” instructions in this manual, 

or see your dealer.

•  When engine starts, 

immediately squeeze and release 

throttle trigger to release fast idle throttle latch, other-

wise severe brake damage will result. 

 

Keep idling for a few minutes. 

•  Set the brake lever in the unlocked position before 

starting to cut.

• 

Squeeze

 throttle trigger gradually and increase revolu

-

tion of the engine. 

•  The chain starts running when the engine reaches 

4400 r/min approximately. 

•  Confirm proper acceleration and lubrication of chain 

and bar. 

•  Do not run the engine at high speed unnecessarily. 

•  Be sure that saw chain stops moving when throttle 

trigger is released.

STOPPING

•  Release throttle trigger and allow engine to idle.

•  Move the control lever to “

STOP

” position.

NOTE

If engine does not stop, move the control lever to 

Cold Start

” (

) position to stop engine. 

Return the unit to your authorized ECHO dealer to 

check and repair stop switch before starting the engine 

again.

CHECKING CHAIN TENSION

  Chain tension should be checked frequently during 

work and corrected as necessary. 

  

   CAUTION

Do not operate with a loose chain.

CHAIN LUBRICATION TEST

Hold the chain just above a dry surface and open the 

throttle to half speed for 30 seconds. 
A thin line of  “thrown” oil should be seen on the dry 

surface.

Summary of Contents for CS-355T





































Reviews: