Echo CS-330MX4 Instruction Manual Download Page 4 | Manualshive

Page: 4 / 28

background image

4

C

ONTENTS

Page

Rules for Safe Operation .................................................................................................. 2
Technical Data ................................................................................................................. 5
Emission Data ................................................................................................................. 6
Description ...................................................................................................................... 6
Nomenclature of Parts ...................................................................................................... 7
Preparation for Use .......................................................................................................... 8
Fuel and Lubricant.......................................................................................................... 10
Operation ....................................................................................................................... 12
- Starting Cold Engine .................................................................................................... 12
- Starting Warm Engine .................................................................................................. 13
- Stopping ...................................................................................................................... 13
Cutting Instructions ......................................................................................................... 14
Maintenance and Care ................................................................................................... 17
Chain and Guide Bar Combinations ............................................................................... 22
Setting the Saw Chain .................................................................................................... 23
Troubleshooting .............................................................................................................. 24
Storage .......................................................................................................................... 24
Correct Use of Chain Brake ........................................................................................... 26
Servicing Information ...................................................................................................... 28

I

NTERNATIONAL

S

YMBOLS

S

Carburetor adjustment
- Idle speed

Carburetor adjustment
- High speed mixture

Wear eyes, ears and head
protection

Carburetor adjustment
- Low speed mixture

Gasoline and oil mixture

Symbol form/shape

Symbol description/application Symbol form/shape Symbol description/application

Chain oiler adjustment

Chain brake operation

Chain oil pump

Chain oil fill

Emergency stop

Choke control “Cold Start”
position (choke closed)

STOP

Read and understand
Operator's Manual.

Finger Sever

«
...
2
3
4
5
6
...
»

Summary of Contents for CS-330MX4





























Reviews:

No comments

Related manuals for CS-330MX4

Brand: Tanaka Pages: 18

Brand: Parkside Pages: 256

Brand: Cramer Pages: 241

Brand: Senix Pages: 72

Brand: FUXTEC Pages: 38

sunjoe iON100V-18CS-CT-RM

Brand: SNOWJOE Pages: 28

Brand: Homelite Pages: 36

Brand: Portland Pages: 24

Brand: Poulan Pro Pages: 16

Brand: Oregon Scientific Pages: 2

Brand: Raider Pages: 156

Brand: Zenoah Pages: 260

YELLOW GARDEN LINE YGL N.G. 2400

Brand: Zgonc Pages: 40

Brand: Einhell Royal Pages: 29

MS 36-18 LTX BL 40

Brand: Metabo Pages: 144

Brand: Urrea Pages: 20

Brand: PowerBase Pages: 44

Brand: Komatsu Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands