background image

1

3 INCH CHIPPER/SHREDDER

ENGLISH

Section

SAFETY

Indicates an imminently hazardous situation that, if not 

avoided, will result in death or serious injury.

DANGER

1.1 SAFETY ALERT SYMBOL

Indicates a potentially hazardous situation that, if not 

avoided, could result in death or serious injury.

WARNING

Indicates a potentially hazardous situation that, if not 

avoided, may result in minor or moderate injury.

CAUTION

The Owner/Operator’s manual uses this symbol to alert 

you of potential hazards. Whenever you see this symbol, 

read and obey the safety message that follows it. Failure 

to obey the safety message could result in personal injury, 

death or property damage.

Federal, state, and local laws may prohibit the operation 

of an internal combustion engine using hydrocarbon 

fuels on any forest covered, brush 

covered or grass covered land or on 

land covered with grain, hay or other 

flammable  agricultural  crops,  without 

an engine spark arrestor in continuous 

effective working order. 

The engine on your power equipment, 

like most outdoor power equipment, is an internal 

combustion engine that burns gasoline or diesel fuel 

(hydrocarbons). If operating your power equipment in 

affected areas, it must be equipped with a spark arrestor 

in continuous effective working order. The spark arrestor 

must be attached to the engine exhaust system in such a 

manner that flames or heat from the system will not ignite 

flammable material.

Failure of the owner/operator of the equipment to comply 

with federal, state, and local laws may subject him or her 

to  fines  and/or  other  penalties.  Contact  your  local  fire 

marshal  or  forest  service  for  specific  information  about 

which regulations apply in your area.

The  standard  muffler  installed  on  the  engine  is  spark 

arrestor capable. Spark arrestors require regular 

maintenance. See the Service & Maintenance section of 

this manual for more information.

Contact  local  fire  authorities  for  laws  or  regulations 

regarding fire prevention requirements.

1.2 FIRE HAZARD INFORMATION

Summary of Contents for Bear Cat SC3306

































Reviews: