background image

MAINTENANCE TIMETABLE 

 
 

The following maintenance timetable is an estimate of the time intervals at which maintenance may 
be  required  only.    This  schedule  must  be  adjusted  to  the  regularity  of  usage,  the  condition  of  the 
intake  water,  the  length  of  time  the  system  is  exposed  to  seawater  and  the  total  running  time 
following each system cleaning. 
 
 

COMPONENT 

MAINTENANCE 
REQUIRED 

TIME INTERVAL 
INTERMITTENT DUTY 

Seawater intake 
strainer 

Inspect and clean intake. 

1000 hrs, or when clogged. 

Pre filters 

Replace or clean elements and  
clean housings. 

100hrs. or when clogged. 

Charcoal flush filter 

Replace element. 

Every 6 months. 

High pressure pump 

Change crankcase oil. 
 
 
 
Change packings, seals  
and “

O

” rings. 

 

Initial change after 50 hrs. 
Every 200 operating hours or 
6 months. 
 
Every 5000 hrs or 2 years. 

R.O. membrane 

When production or salt rejection 
decreases by 15%. 
 
Replace 

Clean with acid and/or 
alkaline cleaning compound. 
 
When cleaning does not 
increase production. 

Flow meter 

*Infuse muriatic acid and rinse well. 
 
 

Whenever dirty. 

 

* Set the diverter valve to the sample position. Disconnect the product water tubing from the product 
port at the membrane vessel and carefully infuse Muriatic acid, KR1 or Ospho with a syringe into 
the product water tubing.  Once the discolouring has cleared, re-connect the tubing, run the system 
and rinse the flow meter with the product water. 

CAUTION: ADHERE TO THE SAFETY ADVISES OF THE CLEANING AGENTS

 

Summary of Contents for 1000-BHL- 2


















Reviews: