Eccotemp EZ-Flush i12, Use & Care Manual

Page: 2 / 36

Product Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locater: Eccotemp.com/locater
Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483
WARNING: If the information in these instructions is not followed exactly,
a fire or explosion may result causing property damage, personal injury
or death.
• Do not store or use gasoline or other flammable vapors and liquids in
the vicinity of this or any other appliance.
• WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your
building.
• Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
• Installation and service must be performed by a qualified installer
service agency or the gas supplier.
Eccotemp Systems, LLC
315-A Industrial Road
Summerville, SC 29483
866-356-1992
AUTOMATIC INSTANTANEOUS WATER HEATER
MODEL #:
i12-NG
SERIAL # :
TYPE GAS:
NATURAL GAS
ONLY Minimum Inlet Gas Pressure:
Minimum Input Rating (Btu per hour):
Maximum Input Rating (Btu per hour):
Volta g e: 120 Volts Maximum Inlet Gas Pressure:
Frequency:
60 Hz
Manifold Pressure:
Amps:
Less than 12 Ampe res
Maximum W orking P ressure:
Recovery
Rating:
SUIT ABLE FOR WA TER (P OT ABLE) H EATING ONLY
As used in this standard, the quantity of water obtained by multiplying the
manufacturer's input rating in Btu per hour by the thermal efficiency and dividing
the product by 825 Btu per gallon. This is based on a 100°F temperature rise, and
a nominal specific heat for water of 8.25 Btu per gallon per degree F.
FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance
This appliance mu s t be in stalled in accordance
with lo cal codes or , in the ab sence of local
c odes, the National Fuel Gas Code, Natural Gas
and Propane Installation Code
80,000
20,000
4” w.c
(1Kpa)
10.5'' w.c
(2.61Kpa)
3.05'' w.c
(0.76Kpa)
150 psi
The temperature and pressure relief valve provided by the manufacturer shall be installed at the
time of installation of the heater in the location specified by the manufacturer. Local codes shall
govern installation of relief devices. For safe operation of the water heater, the relief valve must
not be removed or plugged.
INDOOR USE ONLY
The unit must be installed on a fire retardant area, and must be away from all combustible
materials. Clearance should be 1.75 ft to the left and right side of combustible materials, and
6.75 ft to the front.
Open on three sides and an overhead clearance of 36”
Not recommended in excess of 3,800 ft. above sea level.
Eccotemp Systems, LLC
315-A Industrial Road
Summerville, SC 29483
866-356-1992
AUTOMATIC INSTANTANEOUS WATER HEATER
MODEL #:
i12-LP
SERIAL # :
TYPE GAS:
LIQUID PROPANE
ONLY Minimum Inlet Gas Pressure:
Minimum Input Rating (Btu per hour):
Maximum Input Rating (Btu per hour):
Volta g e: 120 Volts Maximum Inlet Gas Pressure:
Frequency:
60 Hz
Manifold Pressure:
Amps:
Less than 12 Ampe res
Maximum W orking P ressure:
Recovery
Rating:
SUIT ABLE FOR WA TER (P OT ABLE) H EATING ONLY
As used in this standard, the quantity of water obtained by multiplying the
manufacturer's input rating in Btu per hour by the thermal efficiency and dividing
the product by 825 Btu per gallon. This is based on a 100°F temperature rise, and
a nominal specific heat for water of 8.25 Btu per gallon per degree F.
FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance
This appliance mu s t be in stalled in accordance
with lo cal codes or , in the ab sence of local
c odes, the National Fuel Gas Code, Natural Gas
and Propane Installation Code
80,000
20,000
9'' w.c
(2.24 Kpa)
13'' w.c
(3.23Kpa)
4.93'' w.c
(1.22Kpa)
150 psi
The temperature and pressure relief valve provided by the manufacturer shall be installed at the
time of installation of the heater in the location specified by the manufacturer. Local codes shall
govern installation of relief devices. For safe operation of the water heater, the relief valve must
not be removed or plugged.
INDOOR USE ONLY
The unit must be installed on a fire retardant area, and must be away from all combustible
materials. Clearance should be 1.75 ft to the left and right side of combustible materials, and
6.75 ft to the front.
Open on three sides and an overhead clearance of 36”
Not recommended in excess of 3,800 ft. above sea level.