Ebyte E831-RTU(8080T-485) User Manual Download Page 6 | Manualshive

Page: 6 / 22

background image

1.2. Simple use

Wiring: The computer is connected to E831-RTU (8080T-485) via USB to RS485.
Power supply: E831-RTU (8080T-485) working voltage is DC 8 ~ 28V, 12V or 24V is

recommended.

1.2.1. RS485 bus control

Select the corresponding model and port, and click Search to search for the device.

When the device is searched, click "Stop"

«
...
4
5
6
7
8
...
»

Summary of Contents for E831-RTU(8080T-485)























Reviews:

No comments

Related manuals for E831-RTU(8080T-485)

Brand: Gardena Pages: 17

Brand: SAFI Pages: 18

Brand: Badger Meter Pages: 2

Brand: Badger Meter Pages: 48

BadgerTouch HREBT

Brand: Badger Meter Pages: 12

Brand: Badger Meter Pages: 16

Brand: Ublox Pages: 2

Brand: u-blox Pages: 19

Brand: York Pages: 24

Brand: TCi Pages: 9

Brand: GHL Pages: 34

Brand: Comparato Pages: 20

Wattstopper LMIN-104

Brand: LEGRAND Pages: 22

Brand: Eaton Pages: 108

Brand: Carrier Pages: 4

Brand: DMP Electronics Pages: 56

Brand: REMKO Pages: 20

Brand: ARI-Armaturen Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands