background image

Chengdu Ebyte Electronic Technology Co., Ltd.                                                                                                                            E73-2G4M04S1D User manual 

 

           

Copyright ©2012–2018,Chengdu Ebyte Electronic Technology Co.,Ltd.

 

 

5.2 Module is easy to damage 

 

Please check the power supply and ensure it is within  the recommended  range. Voltage  higher than the peak will  lead 
to a permanent damage to the module. 

 

Please check the stability of power supply and ensure the voltage not to fluctuate too much. 

 

Please make  sure anti-static measures are taken when installing and using, high frequency devices have electrostatic 
susceptibility.   

 

Please ensure the humidity  is within limited  range for some parts are sensitive to humidity.   

 

Please avoid using modules under too high or too low temperature. 

5.3 High bit error rate 

 

There are co-channel signal interference nearby, keep away from  interference sources or modify  frequency, channel 
to avoid interference. 

 

Unsatisfactory power supply may also cause garbled characters, and ensure the reliability  of the power supply. 

 

If the extension cable or feeder is of poor quality or too long, the bit error rate will  be high. 

6.

 

Welding  operation  guidance 

6.1

 

Reflow Soldering Temperature 

Profile Feature 

Curve  feature 

Sn-Pb Assembly 

Pb-Free  Assembly 

Solder Paste 

Solder paste 

Sn63/Pb37 

Sn96.5/Ag3/Cu0.5 

Preheat Temperature min 

Tsmin

 

Minimum preheating temperature 

100℃ 

150℃ 

Preheat temperature max  (Tsmax) 

Maximum preheating temperature 

150℃ 

200℃ 

Preheat Time (Tsmin to Tsmax)(ts) 

Preheating time 

60-120 sec 

60-120 sec 

Average  ramp-up rate(Tsmax to Tp) 

Average  rising rate 

3℃/second max 

3℃/second max 

Liquidous Temperature (TL) 

Liquid phase temperature 

183℃ 

217℃ 

Time

tL

M aintained Above

TL

 

Time above liquidus 

60-90 sec 

30-90 sec 

Peak temperature

Tp

 

Peak temperature 

220-235℃ 

230-250℃ 

Aveage  ramp-down rate

Tp to 

Tsmax

 

Average  descent rate 

6℃/second max 

6℃/second max 

Time 25℃ to peak temperature 

Time of 25 ° C to peak temperature 

6 minutes    max 

8 minutes    max 

 

Summary of Contents for E73-2G4M04S1D













Reviews: