background image

Chengdu Ebyte Electronic Technology Co., Ltd

E104-BT10 User Manual

Copyright ©2012–2019

C

hengdu Ebyte Electronic Technology Co., Ltd

4-26

See details from

3.3

Transmitting

08 c2 0002 11223344AA

Receiving

09 0A 42 0001 FFFF 11223344AA

6

FAQ

6.1 Communication range is too short

The communication distance will be affected when obstacle exists.

Data lose rate will be affected by temperature, humidity and co-channel interference.

The ground will absorb and reflect wireless radio wave, so the performance will be poor when testing near ground.

Seawater has great ability in absorbing wireless radio wave, so performance will be poor when testing near the sea.

The signal will be affected when the antenna is near metal object or put in a metal case.

Power register was set incorrectly, air data rate is set as too high (the higher the air data rate, the shorter the
distance).

When the power supply at room temperature is lower than the recommended low voltage, the lower the voltage is,
the lower the transmitting power is.

6.2 Module is easy to damage

Please check the power supply and ensure it is within the recommended range. Voltage higher than the peak will
lead to a permanent damage to the module.

Please check the stability of power supply and ensure the voltage not to fluctuate too much.

Summary of Contents for E104-BT10































Reviews: