Ebyte 2AI User Manual Download

Page: 12 / 35

Chengdu Ebyte Electronic Technology Co.,Ltd.

【

8DO

】

MA01 -XXCX0080 User Manual

，

Chengdu Ebyte Electronic Technology Co.,Ltd.

3.2 Technical parameters

Table 3-2-1 Technical Parameters

category

name

parameter

power supply

Operating voltage DC 8 to 28V
Operating current

50mA @12V

The power supply
indicates

Green LED indication

Serial

Communication
interface

RS485

baud rate

1200 to 115200 bps (default 9600 bps)

The data bit

8 (Fixed).

Check bit

No checks, parity, parity (default no checks)

Stop bit

1 (fixed).

Communication
protocol

Modbus RTU protocol

The

device

address

1 to 247(default address 32:

Software

1, hardware 31).

DO output

The number of
DO roads

8 way

The DO output
type

Type C relay (normally open and normally closed)

DO output mode

Level mode, pulse mode

Relay

contact

capacity

30V/10A

☆

250V/10A

The

output

indicates

Red LED indication

other

Product size

145 mm x 90 mm x 40 mm (W.W.W. High)

Product weight

250g ± 5g

Working
temperature and
humidity

-40 to 85 degrees C, 5% to 95% RH (no condensation)

Store temperature
and humidity

-60 to 125 degrees C, 5% to 95% RH (no
condensation)

How to install it

Positioning hole installation, rail installation

Summary of Contents for 2AI



































Search results

Summary of Contents for 2AI

Reviews:

Related manuals for 2AI

Brands by name

Popular brands

Ebyte 2AI, User Manual

Search results

Summary of Contents for 2AI

Reviews:

Related manuals for 2AI

Brands by name

Popular brands