I
NTRODUCTION
• G
ETTING
S
TARTED
S
PECIFICATIONS
RUPRU
*RUPWKH2OG
DQGKLVVRQ
+DUDOG%OnWDQG
%OXHWRRWK
ZHUHOHJHQGDU\NLQJVDQGFRQTXHURUVLQ6FDQGLQDYLDLQWKH9LNLQJ
$JH,WPLJKWEHVXJJHVWHGWKDW*RUP·VZLOGWHPSHUKDVPDUNHG
WKH6ZHGLVKODQJXDJH7KHZRUG
JRUPD
PHDQVVD\LQJVRPHWKLQJLQD
YHU\ORXGYRLFH
2
BALANCED OUTPUT:
Output Level
nominal
- 10 dBv
Output Impedance
< 10 ohms current lim.
Frequency Response
+0/-3 dB
35 - 20k Hz
Dynamic Range:
linear
102 dB typ.
A-weighted
105 dB min.
XLR Connections
1-GND, 2-Hot, 3-Cold
Options
Pre/Post EQ,
GND LIFT
EFFECTS LOOP:
Loop Signal Level
nominal
-10 dBv
Gain
Unity (1:1)
Output Impedance (Send)
<100 ohms
Input Impedance (Return)
47 kohms // 100 pF
LINE OUT:
Output Impedance:
< 5 kohms
Nominal Signal Level:
0 dBv
REMOTE:
Connection:
RING = Octaver
TIP = Comp/Limit
Function
Connect to GND
for bypass
Threshold
0.7 V
Current
12 mA suitable for LED
POWERAMP/
Continuous Output Power
240 W RMS
CABINET:
Dynamic Output Power
300 W RMS
Cabinet:
Impedance
4 ohms
Crossover Freq. 4.5 kHz
Resonance
75 Hz
Volume
45 l
AUXILIARY INFO:
Power Requirements
max
350 W
Mains Protection:
T3.15A Fuse ( 230V )
T6.3A Fuse ( 117V )
Dimensions:
22.5" (570 mm) Width
13" (330 mm) Depth
20.5” (520 mm) Height
Weight:
71 lbs. ( 32 kg )
Shipping
75 lbs. ( 34 kg )
References:
0 dBv = 0.775 V RMS
Specifications are subject to change without notice!
19
*
9L JUDWXOHUDU GLJ WLOO YDOHW DY EDVFRPERQ
(%6*RUP
(%6 *RUP
lU GHQ PHVW NRPSOHWWD
NUDIWIXOOD RFK IOH[LEOD EDVFRPER VRP
QnJRQVLQ KDU WLOOYHUNDWV 0HG LQE\JJW
GHOQLQJVILOWHU PRQLWRUIXQWLRQ VXSHUDNWLYD
ILOWHURFKGHWNODVVLVND(%6OMXGHWHUEMXGHU
(%6 *RUP
HQ PlQJG P|MOLJKHWHU VRP
EHVNULYVLGHQQDPDQXDO0HQI|UVWDYDOOW
I|OMHU HQ LQWURGXNWLRQ VRP KMlOSHU GLJ DWW
EOLEHNDQW
(%6*RUP
A
TT KOMMA IGÅNG
...
1. Packa försiktigt upp combon.
2. Se till att alla kontroller är ställda fullt
motsols. Fortsätt med att ställa de tre
filterrattarna märkta BASS, MIDDLE
och TREBLE till mittposition. Leta upp
filteromkopplaren och ställ den i läge
BYPASS. Se även till att omkopplaren
märkt Character är i uttryckt läge. Nu
är ljudet i EBS Gorm "nollställt" och
redo för att skapa just ditt personliga
sound.
3. Koppla in din bas.
4. Spela hårt på basen och vrid upp GAIN
ratten tills PEAK dioden börjar blinka.
Än har du inget hörbart ljud, men en
perfekt signal att jobba vidare med.
5. Sök och vrid upp VOLUME ratten till
lämplig ljudnivå.
&RQJUDWXODWLRQVRQ\RXUFKRLFHRIWKH
(%6
*RUP
EDVVJXLWDUFRPER
7KH
(%6 *RUP
LV WKH PRVW SRZHUIXO
YHUVDWLOH DQG FRPSOHWH EDVV FRPER HYHU
EXLOW :LWK EXLOW LQ FURVVRYHU PRQLWRU
VHFWLRQDQGDVXSHUSRZHUIXO(4WKHXQLW
RIIHUV DQ H[WUHPHO\ ZLGH UDQJH RI SRVVL
ELOLWLHV ZKLOH PDLQWDLQLQJ WKDW FODVVLF (%6
VRXQG 7KHVH EULHI WXWRULDOV ZLOO KHOS \RX
WR EHFRPH DFTXDLQWHG ZLWK VRPH RI WKH
IHDWXUHVRIWKH
(%6*RUP
G
ETTING STARTED
...
1. Carefully unpack the bass combo.
2. Check that the controls are set fully
counter clockwise. Proceed by turning
the three filter knobs marked BASS,
MIDDLE and TREBLE to mid position.
Locate the filter switch and set it to
BYPASS. Make also sure that the
switch marked Character is in its’ outer
position. Now the EBS Gorm’s settings
are "zeroed" and ready to be
personalized.
3. Plug in your bass.
4. While plucking the strings as hard as
you would during your hardest playing,
gradually increase the GAIN knob until
the PEAK led starts to flash at peaks.
5. Move over to the VOLUME knob and
adjust for the desired output volume.
