Operating instructions
S4E330-AP20-43
Translation of the original operating instructions
3.2 Nominal data
Motor
M4E068-DF
Phase
1~
1~
Nominal voltage / VAC
230
230
Frequency / Hz
50
60
Type of data definition
fa
fa
Valid for approval /
standard
CE
CE
Speed (rpm) / min
-1
1360
1520
Power input / W
105
135
Current draw / A
0.52
0.6
Motor capacitor / µF
3
3
Capacitor voltage / VDB
400
400
Capacitor standard
S0 (CE)
S0 (CE)
Max. back pressure / Pa
60
70
Min. ambient
temperature / °C
-25
-25
Max. ambient
temperature / °C
65
65
ml = Max. load · me = Max. efficiency · fa = Running at free air
cs = Customer specs · cu = Customer unit
Subject to alterations
3.3 Technical features
Mass
4.1 kg
Size
330 mm
Motor size
68
Surface of rotor
Coated in black
Material of terminal box
PC / ABS plastic
Material of blades
Sheet steel, coated in black
Material of guard grille
Steel, coated in black plastic (RAL9005)
Number of blades
5
Direction of air flow
V
Direction of rotation
Counter-clockwise, seen on rotor
Type of protection
IP44; Depending on installation and
position as per EN 60034-5
Insulation class
"F"
Humidity (F) /
environmental
protection class (H)
H1
Mounting position
Shaft horizontal or rotor on bottom; rotor
on top on request
Condensation
drainage holes
Rotor-side
Operation mode
S1
Motor bearing
Ball bearing
Touch current acc.
IEC 60990 (measuring
network Fig. 4, TN
system)
< 0.75 mA
Electrical connection
Terminal box; Via terminal box, capacitor
integrated and connected
Motor protection
Thermal overload protector (TOP) wired
internally
Cable exit
Axial
Protection class
I (if protective earth is connected by
customer)
Motor capacitor
according to EN 60252-
1 in safety protection
class
S0
Product conforming
to standard
EN 60335-1; CE
Approval
CSA C22.2 no. 100; UL 1004-1
For cyclic speed loads, note that the rotating parts of the device
are designed for maximum one million load cycles. If you have
specific questions, contact ebm-papst for support.
;
Use the device in accordance with its protection type.
Notes on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may vary during the production period.
Strength, dimensional stability and dimensional accuracy are not affected
by this.
The colour pigments of the paints used react perceptibly to UV light over
the course of time. This does not however have any influence on the
technical properties of the products. To prevent the formation of patches
and fading, the product is to be protected against UV radiation. Changes
in colour are not a reason for complaint and are not covered by the
warranty.
3.4 Mounting data
;
Secure the mounting screws against accidentally coming loose (e.g.
by using self-locking screws).
Strength class for
mounting screws
8.8
Any further mounting data required can be taken from the product
drawing or Section chapter 4.1 Connecting the mechanical system.
3.5 Transport and storage conditions
Max. permissible
ambient motor temp.
(transp./ storage)
+ 80 °C
Min. permissible
ambient motor temp.
(transp./storage)
- 40 °C
Item no. 14634-5-9970 · ENG · Revision 206792 · Release 2019-11-18 · Page 5 / 11
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com
