Operating instructions
D2E160-GL25-23
Translation of the original operating instructions
3.2 Nominal data
Motor
M2E074-HA
Phase
1~
Nominal voltage / VAC
230
Frequency / Hz
50
Method of obtaining
data
ml
Valid for approval/
standard
CE
Speed (rpm) / min
-1
2200
Power consumption / W
390
Current draw / A
1.7
Capacitor / µF
10
Capacitor voltage / VDB
400
Capacitor standard
S2 (CE)
Min. back pressure / Pa
330
Min. ambient
temperature / °C
-25
Max. ambient
temperature / °C
45
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Data according to Commission Regulation (EU) 327/
2011
Actual
Req. 2015
01 Overall efficiency η
es
/ %
34.3
34.3
02 Measurement category
A
03 Efficiency category
Static
04 Efficiency grade N
44
44
05 Variable speed drive
No
06 Year of manufacture
The year of manufacture is specified on the
product's rating label.
07 Manufacturer
ebm-papst Mulfingen GmbH & Co. KG
Amtsgericht (court of registration) Stuttgart ·
HRA 590344
D-74673 Mulfingen
08 Type
D2E160-GL25-23
09 Power consumption P
e
/ kW
0.29
09 Air flow q
v
/ m³/h
750
09 Pressure increase total p
sf
/
Pa
476
10 Speed (rpm) n / min
-1
2590
11 Specific ratio
*
1.00
12 Recycling/disposal
Information on recycling and disposal is
provided in the operating instructions.
13 Maintenance
Information on installation, operation and
maintenance is provided in the operating
instructions.
14 Additional components
Components used to calculate the energy
efficiency that are not apparent from the
measurement category are detailed in the
CE declaration.
*
Specific ratio = 1 + p
fs
/ 100 000 Pa
Data obtained at optimum efficiency level. The ErP data is determined using a motor-impeller
combination in a standardized measurement setup.
3.4 Technical description
Weight
6.9 kg
Size
160 mm
Motor size
74
Rotor surface
Unpainted
Terminal box material
PP plastic
Impeller material
Sheet steel, galvanized
Housing material
PP plastic
Motor suspension
Motor vibration-damped on both sides
Direction of rotation
Counterclockwise, viewed toward rotor
Degree of protection
IP20
Insulation class
"F"
Moisture (F) /
Environmental (H)
protection class
H0 - dry environment
Installation position
Any
Condensation
drainage holes
None
Mode
S1
Motor bearing
Ball bearing
Speed levels
3
Touch current
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
< 0.75 mA
Electrical hookup
Connector with cable; Via terminal box,
capacitor integrated and connected
Motor protection
Thermal overload protector (TOP) with
basic insulation
with cable
Axial
Protection class
I (with customer connection of protective
earth)
Motor capacitor
according to EN 60252-
1 in safety protection
class
S2
Conformity with
standards
EN 60335-1; CE
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
;
Use the device in accordance with its degree of protection.
Information on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
accuracy.
The color pigments in the paints used perceptibly react to UV light over
the course of time. This does not however in any way affect the
technical properties of the products. The product is to be protected against
UV radiation to prevent the formation of patches and fading. Changes in
color are not a reason for complaint and are not covered by the warranty.
Item no. 13132-5-9970 · ENU · Change 202174 · Approved 2018-12-28 · Page 5 / 10
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com