background image

18

FCC Information to User

This equipment has been tested and found to comply with the limits 

for a Class B digital device, pursuant to Part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against 

harmful interference in a residential installation. This equipment 

generates, uses and can radiate radio frequency energy and, if not 

installed and used in accordance with the instructions, may cause 

harmful interference to radio communications. However, there is no 

guarantee that interference will not occur in a particular installation. 

If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment 

off and on, the user is encouraged to try to correct the interference 

by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment 

  and receiver.

• Connect the equipment into an outlet on a circuit  

  

different from that to which the receiver 

  is connected. 

• Consult the dealer or an experienced radio/TV  

  

technician for help.

Caution

Modifications not expressly approved by the party responsible for 

compliance could void the user’s authority to operate the equipment.

FCC Compliance Information: This device complies with Part 15 of 

the FCC Rules. Operation is subject to the following two conditions: 

(1) This device may not cause harmful interference, and (2) this 

device must accept any interference received, including interference 

that may cause undesired operation.

CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN 

INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO 

THE INSTRUCTIONS.

Complies with

IDA Standards

DA103548

Summary of Contents for SMARTMARKER





















Reviews: