EBARA DML Instruction Manual Download

Page: 18 / 18

- 18 -

EBARA

Corporation

’s

control.

(d) If the trouble is caused by use of parts other than those recommended by EBARA.

(e) If the trouble is caused by repair or remodeling of the pump carried out by a party other than

EBARA or agent specified by EBARA.

(f)

“Consumable items” refer to lubrication oil, gasket, seal washer, O-ring, mechanical seal,
and other parts that will eventually require replacement.

(3) EBARA

’s liability shall not extend to any other costs beyond the above.

(4) The storage period of consumable items is 7 years after manufacturing stop.

12 Repair and After-sale service

If any abnormality is detected during the operation of the product, immediately stop the operation, and

inspect to identify whether the abnormality is defective or not. (Refer to 8 "Troubleshooting"). If the

abnormality is defective one, promptly notify the matter to EBARA or related agencies which contact

addresses are listed at the end of this Instruction Manual, with the information about the description given

on the nameplate and the condition of the failure (abnormality).

Note

Packing materials after installation, and wasted lubricant oil and grease, and parts after

inspection and repair shall be transferred to a qualified waste-treatment contractor

observing the applicable laws and the regional regulations.

For any question about your pump, please inquire the matter to EBARA CORP. without hesitation.

Ebara Engineering Singapore Pte. Ltd.

Website: www.ebara.com.sg

E-mail: [email protected]

Ebara Pumps Malaysia Sdn. Bhd.

Website: www.ebara.com.my

E-mail: [email protected]

P.T. Ebara Indonesia

Website: www.ebaraindonesia.com

E-mail: [email protected]

Ebara (Thailand) Limited

Website: www.ebara.co.th

E-mail: [email protected]

Ebara Pumps Philippines,inc.

Website: www.ebaraphilippines.com

E-mail: [email protected]

<China>

Ebara Machinery (China) Co., Ltd.

Website: www.ebara.cn

E-mail: [email protected]

Ebara Corporation (Japan)

Standard Products Business Office

Website: www.ebara.co.jp/en

Summary of Contents for DML



















Search results

Summary of Contents for DML

Reviews:

Related manuals for DML

Brands by name

Popular brands

EBARA DML, Instruction Manual

Search results

Summary of Contents for DML

Reviews:

Related manuals for DML

Brands by name

Popular brands