EBARA DGFMU Operating Instructions, Installation & Maintenance Manual Download Page 15

EBARA Submersible Grinder Pumps

DGUII/DGFU

Operating, Installation, and Maintenance

EBARA

Fluid Handling

www.pumpsebara.com

15

(t) 803  327-5005  •  (f) 803  327-5097

rev. 11/05

Warranty Information

1. All specifications subject to change without notice

2. Limited warranty:

EIC warrants for a period of twelve months from the date of initial startup or eighteen months from the date 
of shipment, whichever shall first occur (the “Warranty Period”) the EIC Products to be delivered hereunder 
against defects in material and workmanship, under normal use and service when installed, used and main-
tained in accordance with instructions supplied by EIC. This is EIC’s sole and exclusive warranty. It applies 
only to EIC Products and specifically excludes Other Equipment, whether or not such Other Equipment is 
included in EIC’s scope of supply hereunder. Such Other Equipment is warranted only by its manufacturer. If 
such a defect appears in EIC Products within the Warranty Period and Purchaser has given EIC immediate 
written notice of same, EIC will either repair the part, or at its option replace the part, by shipping a similar 
part F.O.B. EIC’s shipping point, or at its option refund an equitable portion of the purchase price. EIC may 
require the return of the defective part, transportation prepaid, to establish the claim. All costs of removal, 
reinstallation, field labor and transportation shall be borne by the Purchaser. No allowance will be made for 
repairs without EIC’s written consent or approval, and the Warranty Period shall not be suspended upon 
stopping operation for warranty repairs, nor recommence upon completion of the warranty repairs, but shall 
run continuously from commencement until normal expiration. Repair parts shall carry no greater warranty 
than the remaining balance of the underlying EIC Product into which they may be installed, expiring at the 
same time as said underlying warranty.

Any descriptions of the EIC Products or Other Equipment, any specifications, and any samples, models, 
bulletins, or similar material used in connection with this sale are for the sole purpose of identifying the said 
Equipment and are not to be construed as express or implied warranties. Unless during the warranty period 
all repairs or replacements or parts or components for EIC Products are with EIC-approved parts or compo-
nents, and all warranty service is performed by EIC or its authorized distributor or representative, the warranty
responsibility of EIC shall immediately terminate.

EIC makes no other warranty of any kind whatsoever, express or implied; and all warranties of merchantability
and fitness for a particular purpose are hereby disclaimed by EIC and excluded from these conditions. The 
Purchaser’s sole and exclusive remedy, whether upon warranty, contract or tort, including negligence, will be 
to proceed under this warranty. All liability of EIC shall terminate no later than the expiration of the Warranty 
Period.

Summary of Contents for DGFMU

















Reviews: