EAW N T L 7 2 0 Owner'S Manual Download Page 5

1 . 2

E C   D e c l a r a t i o n   o f   C o n f o r m i t y

Manufacturer:

Eastern Acoustic Works — USA

Declares that the following product(s) have been tested and passed all relevant requirements as
described below by the appropriate European Directives as they apply to Professional Audio Products.

Product Model:

NTL720

Product Description:

Self-powered loudspeaker

Safety Directive(s):

EN 60065-2002 

EMC Directive(s):

EN 55103-1 (Radiated/Conducted Emissions)
EN 55103-2 (Radiated/Conducted Immunity)
2004/108/EEC Directive

Low Voltage Directive:

72/23/EEC

Markings Directive:

93/68/EEC

The Technical Report/File is maintained at:

LOUD Technologies Inc.
16220 Wood-Red Road NE
Woodinville, WA 98072 USA
Authorized Representative:

Tel: +1 425 892 6500

Kevin Cyrus  

Tel: +1 866 858 5832

Director of Compliance

Fax: +1 425 487 4337

LOUD Technologies Inc.

e-mail: [email protected] 

Issued: February, 2008

1 . 3

F C C   C o m p l i a n c e

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense. 

CAUTION:

Changes or modifications not expressly approved by LOUD Technologies could void the

user's authority to operate the equipment.

Correct disposal of this product.

This symbol indicates that this product should not be

disposed of with your household waste, according to the WEEE Directive (2002/96/EC)
and your national law. This product should be handed over to an authorized collection site
for recycling waste electrical and electronic equipment (EEE). Improper handling of this
type of waste could have a possible negative impact on the environment and human health
due to potentially hazardous substances that are generally associated with EEE. At the
same time, your cooperation in the correct disposal of this product will contribute to the

effective usage of natural resources. For more information about where you can drop off your waste
equipment for recycling, please contact your local city office, waste authority, or your household waste
disposal service. 

v

Summary of Contents for N T L 7 2 0





































Reviews: