background image

4

 – CAM150 / CAM60

CAM150 / CAM60 – 

5

3. FRONT PANEL FEATURES

1.  INPUT LEVEL

These controls allow you to individually adjust the volume 

level of each of the four balanced inputs, and the Aux 

input. We recommend that you turn down the level controls 

of any unused or little-used inputs.

2.  EQ-LO

Turn this clockwise to boost the level of the low-frequency 

range below 100 Hz. Turn it counter-clockwise to cut the 

level. In the center position, there is no change in level. 

The maximum boost and cut is 10 dB at 100 Hz.

3.  EQ-HI

Turn this clockwise to boost the level of the high-frequency 

range above 10 kHz. Turn it counter-clockwise to cut the 

level. In the center position, there is no change in level. 

The maximum boost and cut is 10 dB at 10 kHz.

4.  MASTER VOLUME

Use this volume control to adjust the sound output level 

to your speakers. Adjust the master level and the input 

levels to average settings, not too high and not too low. 

For example, if you find you have to turn the master volume 

up high, then the input level controls might be set too low. 

If the master volume becomes loud after a small rotation, 

then the input level controls might be set too high.

5.  LED METER

This meter shows the signal level reaching the input 

section of the main power amplifier. 

The lower eight LEDs represent the area between -20 dB 

and 0 dB. Adjust the Master Volume to keep your output 

within these levels.

Make sure the top two LEDs are not lit, or the outgoing 

signal will clip and distort. Turn down the Master Volume 

level so the top two LEDs do not light.

� � � � � � �

��������

���������������������

��������������������

������������������

��������������������

�����������������������

�������

�������

�������

�������

�������

���

���

���

���

���

�����

��

��������

���

������

��������

��

��

����

����

����

����

�����������

��

���

�����

���

�������������������������

��

�������

���

����

���

�������

���

����

���

�������

���

����

���

�������

���

����

���

����������

������������

�������������

�������������

©  2004  LOUD  TECHNOLOGIES  INC.

"EAW"  IS  A  REGISTERED  TRADEMARK 

OF  LOUD  TECHNOLOGIES  INC.

CAM150-MIXER AMPLIFIER

6.  POWER SWITCH

Use this switch to turn the unit on or off. The power is on 

when the top of the switch is pressed, and off when the 

bottom is pressed. Turn it off if you are not using the unit 

for long periods of time.

1

2

3

4

5

6

Summary of Contents for CAM150













Reviews: